Proper Use; Technical Data - EINHELL TC-MS 3017 T Manual De Instrucciones Original

3. Proper use

The crosscut and miter saw with table is desig-
ned for cross-cutting and for the longitudinal and
lateral cutting (with cross stop only) of wood and
plastic suitable for the machine size.
The machine is not to be used for cutting fi re
wood. The machine is to be used only for its
prescribed purpose.Any use other than that men-
tioned is considered to be a case of misuse. The
user/operator and not the manufacturer shall be
liable for any damage or injury resulting from such
cases of misuse. The machine is to be operated
only with suitable saw blades. It is prohibited to
use any type of cutting-off wheel.
To use the machine properly you must also obser-
ve the safety regulations, the assembly instruc-
tions and the operating instructions to be found in
this manual.All persons who use and service the
machine have to be acquainted with this manual
and must be informed about its potential hazards.
It is also imperative to observe the accident pre-
vention regulations in force in your area.
The same applies for the general rules of occupa-
tional health and safety.
The manufacturer shall not be liable for any chan-
ges made to the machine nor for any damage
resulting from such changes.
Even when the machine is used as prescribed it
is still impossible to eliminate certain residual risk
factors. The following risks may arise due to the
machine's design and setup:
•
Contact with the saw blade in the uncovered
saw zone.
•
Reaching into the running saw blade (cut
injuries).
•
Kick-back of workpieces and parts of workpi-
eces.
•
Saw blade fracturing.
•
Catapulting of faulty carbide tips from the saw
blade.
•
Damage to hearing if essential ear-muffs are
not worn.
•
Harmful emissions of wood dust when the
machine is used in closed rooms.
The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse. The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
Anl_TC_MS_3017_T_SPK7.indb 23 Anl_TC_MS_3017_T_SPK7.indb 23
GB
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.

4. Technical data

AC motor ................................. 230-240 V ~ 50 Hz
Power ...................................................... 2000 W
Operating mode ............................................... S1
Idling speed n .....................................4200 min
0
Carbide saw blade .............ø 305 x ø 30 x 3,2 mm
Number of teeth ............................................... 40
Extractor socket ......................................ø 36 mm
Weight......................................... approx. 17.5 kg
For use as a bench-type saw:
Saw table ....................................... 466 x 400 mm
Cutting depth .................................... max. 50 mm
Minimum size of the workpiece 15 x 10 x 100 mm
Parallel stop .....Can be pivoted from -45° to + 45°
For use as a crosscut saw:
Pivoting range ............................... -45° / 0° / +45°
Miter cut ................................. 0° to 45° to the left
Saw width at 90° ............................. 170 x 85 mm
Saw width at 45° ............................. 110 x 85 mm
Saw width at 2 x 45°
(Double miter cut to the left) ............... 75 x 50 mm
(Double miter cut to the right) ........... 110 x 50 mm
Minimum size of the workpiece 50 x 10 x 100 mm
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 61029.
Sound pressure level L
Uncertainty K ............................................. 3 dB
pA
Sound power level L ....................... 112.1 dB(A)
WA
Uncertainty K ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
- 23 -
-1
................... 99.1 dB(A)
pA
21.12.2016 17:37:41 21.12.2016 17:37:41