Continuous Operation - EINHELL TE-ID 1050 CE Manual De Instrucciones Original

enough for the additional handle to be slid
over the chuck (1) and on to the hammer drill.
•
After you have positioned the additional
handle (8), turn it to the most comfortable
working position for you.
•
Now turn the handle in the opposite direction
again until the additional handle is secure.
•
The additional handle (8) is suitable for both
left-handed and right-handed users.
5.2 Fitting and adjusting the depth stop
(Fig. 4/Item 2)
•
Undo the thumb screw (a) on the additional
handle (8) and insert the depth stop (2) in the
hole of the additional handle.
•
Set the depth stop and retighten the thumb
screw.
•
Now drill the hole until the depth stop touches
the workpiece.
5.3 Fitting the drill bit (Fig. 10)
Always pull the power plug before making adjust-
ments to the equipment.
•
Release the depth stop as described in 5.2
and push it towards the additional handle.
This provides free access to the chuck (1).
•
This hammer drill is fitted with a keyless
chuck (1).
•
Open the chuck (1). The drill bit opening must
be large enough to fit the drill bit into.
•
Select a suitable drill bit. Push the drill bit as
far as possible into the chuck opening.
•
Close the chuck (1). Check that the drill bit is
secure in the chuck (1).
•
Check at regular intervals that the drill bit or
tool is secure (pull the mains plug).
5.4 Fitting the dust extraction system
(Fig. 5-9)
The dust extraction system (11) is fi tted on the
additional handle (8). It can also be used in com-
bination with the depth stop (2). This prevents the
work area becoming very dirty.
•
Release the cover (A) and the sealing cap (B)
by turning the additional handle (8). Several
drill bits can be stored in the sealing cap (B)
to save space (Fig. 5-6).
•
Screw the dust extractor adapter (9) on to the
additional handle (8) from underneath.
•
Now place the dust extraction system (11) on
to the additional handle (8) as shown in Fig.
7 – 8 and secure it by turning it.
Anleitung_TE_ID_1050_CE_SPK7.indb 19 Anleitung_TE_ID_1050_CE_SPK7.indb 19
GB
Important. There are detents on the cover (A)
and the dust extraction system (11) which
must be engaged in the corresponding re-
cesses on the additional handle (8) before
the cover (A) or dust extraction system (11)
can be turned and locked.
•
Remove the dust extraction system (11) by
following the above in reverse.
•
Fit the additional handle (8) on the machine
as described in 5.1. Please note that the
additional handle (8) must be fitted to the left-
hand side of the machine if the dust extrac-
tion system (11) is also fitted (Fig. 9).
•
The dust extraction system (11) can be fitted
to the machine even if the additional handle
(8) is fitted.
•
If the dust extraction system (11) is not re-
quired, the cover (A) and the sealing cap (B)
must be fitted to the additional handle (8).
6. Operation
6.1 ON/OFF switch (Fig. 11/Item 5)
•
First fit a suitable drill bit into the tool (see
5.3).
•
Connect the mains plug to a suitable socket.
•
Position the drill in the position you wish to
drill.
To switch on:
Press the ON/OFF switch (5)

Continuous operation:

Secure the ON/OFF switch (5) with the locking
button (4).
To switch off :
Press the ON/OFF switch (5) briefl y.
6.2 Adjusting the speed (Fig. 11/Item 5)
You can infi nitely vary the speed whilst using the
tool.
•
Select the speed by applying a greater or les-
ser pressure to the ON/OFF switch (5).
•
Select the correct speed: The most suitable
speed depends on the workpiece, the type of
use and the drill bit used.
•
Low pressure on the ON/OFF switch (5): Lo-
wer speed (suitable for: small screws and soft
materials)
•
Greater pressure on the ON/OFF switch (5):
Higher speed (suitable for large/long screws
- 19 -
01.07.2020 08:05:10 01.07.2020 08:05:10