English
cutting operations where the saw blade
cuts completely through the thickness of
the workpiece, the guard and other safety
devices help reduce the risk of injury.
Immediately reattach the guarding system
–
after completing an operation (such as
rabbeting, dadoing or resawing cuts)
which requires removal of the guard, riv
ing knife and/or anti-kickback device. The
guard, riving knife, and anti-kickback de
vice help to reduce the risk of injury.
Make sure the saw blade is not contacting
–
the guard, riving knife or the workpiece
before the switch is turned on. Inadvertent
contact of these items with the saw blade
could cause a hazardous condition.
–
Adjust the riving knife as described in this
instruction manual. Incorrect spacing, po
sitioning and alignment can make the riving
knife ineffective in reducing the likelihood
of kickback.
–
For the riving knife and anti-kickback de
vice to work, they must be engaged in the
workpiece. The riving knife and anti-kick
back device are ineffective when cutting
workpieces that are too short to be engag
ed with the riving knife and anti-kickback
device. Under these conditions a kickback
cannot be prevented by the riving knife and
anti-kickback device.
Use the appropriate saw blade for the riv
–
ing knife. For the riving knife to function
properly, the saw blade diameter must
match the appropriate riving knife and the
body of the saw blade must be thinner than
the thickness of the riving knife and the
cutting width of the saw blade must be wid
er than the thickness of the riving knife.
2) Cutting procedures warnings
DANGER: Never place your fingers
–
or hands in the vicinity or in line with the
saw blade. A moment of inattention or a
slip could direct your hand towards the saw
blade and result in serious personal injury.
–
Feed the workpiece into the saw blade or
cutter only against the direction of rota
tion. Feeding the workpiece in the same di
rection that the saw blade is rotating above
the table may result in the workpiece, and
your hand, being pulled into the saw blade.
–
Never use the mitre gauge to feed the
workpiece when ripping and do not use
the rip fence as a length stop when cross
cutting with the mitre gauge. Guiding the
26
workpiece with the rip fence and the mitre
gauge at the same time increases the like
lihood of saw blade binding and kickback.
–
When ripping, always apply the workpiece
feeding force between the fence and the
saw blade. Use a push stick when the dis
tance between the fence and the saw
blade is less than 150 mm, and use a push
block when this distance is less than 50
mm. "Work helping" devices will keep your
hand at a safe distance from the saw blade.
Use only the push stick provided by the
–
manufacturer or constructed in accord
ance with the instructions. This push stick
provides sufficient distance of the hand
from the saw blade.
–
Never use a damaged or cut push stick. A
damaged push stick may break causing
your hand to slip into the saw blade.
Do not perform any operation "freehand".
–
Always use either the rip fence or the mi
tre gauge to position and guide the work
piece. "Freehand" means using your hands
to support or guide the workpiece, in lieu of
a rip fence or mitre gauge. Freehand saw
ing leads to misalignment, binding and
kickback.
–
Never reach around or over a rotating saw
blade. Reaching for a workpiece may lead
to accidental contact with the moving saw
blade.
Provide auxiliary workpiece support to the
–
rear and/or sides of the saw table for long
and/or wide workpieces to keep them lev
el. A long and/or wide workpiece has a ten
dency to pivot on the table's edge, causing
loss of control, saw blade binding and kick
back.
Feed workpiece at an even pace. Do not
–
bend or twist the workpiece. If jamming
occurs, turn the tool off immediately, un
plug the tool then clear the jam. Jamming
the saw blade by the workpiece can cause
kickback or stall the motor.
Do not remove pieces of cut-off material
–
while the saw is running. The material may
become trapped between the fence or in
side the saw blade guard and the saw blade
pulling your fingers into the saw blade.
Turn the saw off and wait until the saw
blade stops before removing material.
Use an auxiliary fence in contact with the
–
table top when ripping workpieces less
than 2 mm thick. A thin workpiece may