Switching On And Off - Metabo W 750-115 Instrucciones De Manejo

en ENGLISH
6 mm! In this case, use the 2-hole nut (10) with 2-
hole spanner (11).
- Lock the spindle (see chapter 6.1).
- Flip up the clip (13) on the clamping nut.
- Fit the clamping nut (12) on the spindle (2). See
illustration on page 2.
- Tighten the clamping nut on the clip (13)
manually in a clockwise direction.
- Flip down the clip (13) again .
Release the (tool-free) clamping nut (12):
- Lock the spindle (see chapter 6.1).
- Flip up the clip (13) on the clamping nut.
- Unscrew the clamping nut (12), turning it
anticlockwise manually .
Note: If the clamping nut (12) is very tightly secured
(12), you can also use a two-hole spanner to
unscrew it.
7. Use
7.1

Switching on and off

Always guide the machine with both hands.
Switch on first, then guide the accessory
towards the workpiece.
The machine must not be allowed to draw in
additional dust and shavings. When switching
the machine on and off and keep it away from dust
deposits. After switching off the machine, only set it
down when the motor has come to a standstill.
Avoid inadvertent starts: always switch the
tool off when the plug is removed from the
mains socket or if there has been a power cut.
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine with
both hands using the handles provided, stand
securely and concentrate.
Machines with a slide switch:
Switching on: push the slide switch (4) forwards.
For continuous operation, tilt it downwards until it
engages.
Switching off: press the rear end of the slide switch
(4) and release it.
Machine with paddle switch (with deadman
function):
(Machines with the designation WP...)
Switching on: Slide the switch-on lock (7) in the
direction of the arrow and press the trigger (6).
Switching off: Release the trigger switch (6).
10
4
I
0
6 7 6 6 7
I
0
7.2 Working Directions
Grinding and sanding operations:
Press down the machine evenly on the surface and
move it back and forth so that the surface of the
workpiece does not become too hot.
Rough grinding: position the machine at an angle of
30° - 40° for the best working results.
Cut-off grinding:
Always work against the run of the disc
(see illustration). Otherwise the
machine may kick back from the cut in
an out of control manner. Guide the
machine evenly at a speed suitable for
the material being processed. Do not tilt, apply
excessive force or sway from side to side.
Wire brushing:
Press down the machine evenly.
8. Cleaning
Particles may become deposited inside the power
tool during operation. This impairs the cooling of the
power tool. Conductive build-up can impair the
protective insulation of the power tool and create an
electrical hazard.
The power tool should be cleaned regularly, often
and thoroughly through all front and rear air vents
using a vacuum cleaner or by blowing in dry air.
Before doing so, separate the power tool from the
power source and wear protective goggles and a
dust mask. Ensure appropriate suction is available
when blowing out vents.
9. Accessories
Use only genuine Metabo accessories.
See page 4.
Only use accessories which fulfil the requirements
and specifications listed in these operating
instructions.
A Cutting guard clip / guard for cut-off
grinding
Designed for work with cutting disc and diamond
cutting discs. Once the cutting guard clip is fitted,
the safety guard becomes a cutting guard.
B Extraction guard for cut-off grinding
Designed for cutting through stone slabs with
diamond cutting discs. With nozzle for extracting
stone dust using a suitable extraction unit.
C Hand protection
Intended for work with backing pads, sanding
plates, wire brushes and support plates, sanding
pads, wire brushes and diamond drill bits for tiles.
Install the hand guard under the additional side-
mounted handle.
D Two hole nut (10)
E Clamping nut (tool-free) (12)
For a complete range of accessories, see
www.metabo.com or the accessories catalogue.