Installing The Outdoor Unit - Mitsubishi Electric PUZ-A18-NHA6 Para El Instalador

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

 ,QVWDOODWLRQ ORFDWLRQ
)LJ 
 9HQWLODWLRQ DQG VHUYLFH VSDFH
 :LQG\ ORFDWLRQ LQVWDOODWLRQ
When installing the outdoor unit on a rooftop or other location unprotected from the
wind, situate the air outlet of the unit so that it is not directly exposed to strong winds.
6WURQJ ZLQG HQWHULQJ WKH DLU RXWOHW PD\ LPSHGH WKH QRUPDO DLUÀRZ DQG D PDOIXQFWLRQ
may result.
The following shows three examples of precautions against strong winds.
1 Face the air outlet towards the nearest available wall about 50 cm, 19-11/16 inch
away from the wall. (Fig. 2-3)
2 Install an optional air outlet guide and air guide if the unit is installed in a location
where strong winds from a typhoon, etc. may directly enter the air outlet. (Fig. 2-4)
A Air outlet guide
3 Position the unit so that the air outlet blows perpendicularly to the seasonal wind
direction, if possible. (Fig. 2-5)
B Wind direction

3. Installing the outdoor unit

B
A M10(3/8") bolt
B Base
C As long as possible.
D Vent
E Set deep in the ground.
A12, A18
Min. 25-19/32
19-11/16
19-11/16
Min. 13-25/32
5-29/32
5-29/32
31-1/2
4
)LJ 

B
)LJ 
A
E
C
A12, A18
A24-A42
D
A24-A42
Min. 14-3/16
23-5/8
23-5/8
Min. 13/32
6-7/8
37-13/32
Fig. 3-1
 :KHQ LQVWDOOLQJ D VLQJOH RXWGRRU XQLW 5HIHU WR WKH ODVW SDJH
Minimum dimensions are as follows, except for Max., meaning Maximum dimen-
sions, indicated.
7KH ¿JXUHV LQ SDUHQWKHVHV DUH IRU $ PRGHOV
5HIHU WR WKH ¿JXUHV IRU HDFK FDVH
1 Obstacles at rear only (Fig. 2-6)
2 Obstacles at rear and above only (Fig. 2-7)
A
3 Obstacles at rear and sides only (Fig. 2-8)
* 350 mm, 13-25/32 inch for A12, A18
4 Obstacles at front only (Fig. 2-9)
* When using an optional air outlet guide, the clearance for A42 models is 500 mm,
19-11/16 inch or more.
5 Obstacles at front and rear only (Fig. 2-10)
* When using an optional air outlet guide, the clearance for A42 models is 500 mm,
19-11/16 inch or more.
6 Obstacles at rear, sides, and above only (Fig. 2-11)
* 350 mm, 13-25/32 inch for A12, A18
‡ 'R QRW LQVWDOO WKH RSWLRQDO DLU RXWOHW JXLGHV IRU XSZDUG DLUÀRZ
 :KHQ LQVWDOOLQJ PXOWLSOH RXWGRRU XQLWV 5HIHU WR WKH ODVW SDJH
Leave 350 mm, 13-25/32 inch for A18 and 10 mm, 13/32 inch for A24-A42 space or
more between the units.
1 Obstacles at rear only (Fig. 2-12)
2 Obstacles at rear and above only (Fig. 2-13)
‡ 1R PRUH WKDQ WKUHH XQLWV PXVW EH LQVWDOOHG VLGH E\ VLGH ,Q DGGLWLRQ OHDYH VSDFH DV VKRZQ
‡ 'R QRW LQVWDOO WKH RSWLRQDO DLU RXWOHW JXLGHV IRU XSZDUG DLUÀRZ
3 Obstacles at front only (Fig. 2-14)
* When using an optional air outlet guide, the clearance for A42 models is 1000 mm,
39-3/8 inch or more.
4 Obstacles at front and rear only (Fig. 2-15)
* When using an optional air outlet guide, the clearance for A42 models is 1000 mm,
39-3/8 inch or more.
5 Single parallel unit arrangement (Fig. 2-16)
* :KHQ XVLQJ DQ RSWLRQDO DLU RXWOHW JXLGH LQVWDOOHG IRU XSZDUG DLUÀRZ WKH FOHDUDQFH LV 
(1000) mm, 19-11/16 (39-3/8) inch or more.
6 Multiple parallel unit arrangement (Fig. 2-17)
* :KHQ XVLQJ DQ RSWLRQDO DLU RXWOHW JXLGH LQVWDOOHG IRU XSZDUG DLUÀRZ WKH FOHDUDQFH LV 
(1500) mm, 39-3/8 (59-1/16) inch or more.
7 Stacked unit arrangement (Fig. 2-18)
‡ 7KH XQLWV FDQ EH VWDFNHG XS WR  XQLWV KLJK
‡ 1R PRUH WKDQ WZR VWDFNHG XQLWV PXVW EH LQVWDOOHG VLGH E\ VLGH ,Q DGGLWLRQ OHDYH VSDFH DV
shown.
‡ %H VXUH WR LQVWDOO WKH XQLW LQ D VWXUG\ OHYHO VXUIDFH WR SUHYHQW UDWWOLQJ QRLVHV GXULQJ
(inch)
peration. (Fig. 3-1)
)RXQGDWLRQ VSHFL¿FDWLRQV!
Foundation bolt
Thickness of concrete
Length of bolt
g
Weight-bearing capacity
g
g
p
‡ 0DNH VXUH WKDW WKH OHQJWK RI WKH IRXQGDWLRQ EROW LV ZLWKLQ  PP  LQFK RI WKH
bottom surface of the base.
‡ 6HFXUH WKH EDVH RI WKH XQLW ¿UPO\ ZLWK IRXU0 IRXQGDWLRQ EROWV LQ VWXUG\ ORFDWLRQV
D
Installing the outdoor unit
‡ 'R QRW EORFN WKH YHQW ,I WKH YHQW LV EORFNHG RSHUDWLRQ ZLOO EH KLQGHUHG DQG EUHDN-
down may result.
‡ ,Q DGGLWLRQ WR WKH XQLW EDVH XVH WKH LQVWDOODWLRQ KROHV RQ WKH EDFN RI WKH XQLW WR
attach wires, etc., if necessary to install the unit. Use self-tapping screws (ø5 × 15
mm, ø13/16 × 19/32 inch or less) and install on site.
Warning:
‡ 7KH XQLW PXVW EH VHFXUHO\ LQVWDOOHG RQ D VWUXFWXUH WKDW FDQ VXVWDLQ LWV ZHLJKW
If the unit is mounted on an unstable structure, it may fall down and cause
damage or injuries.
‡ 7KH XQLW PXVW EH LQVWDOOHG DFFRUGLQJ WR WKH LQVWUXFWLRQV LQ RUGHU WR PLQLPL]H
the risk of damage from earthquakes, typhoons, or strong winds. An incor-
(inch)
rectly installed unit may fall down and cause damage or injuries.
6-7/8
M10 (3/8")
120 mm, 4-23/32 inch
70 mm, 2-3/4 inch
y
320 kg, 264 lbs
g

Publicidad

Tabla de contenido
loading

Tabla de contenido