Cleaning And Maintenance; Emptying The Dust Container - SOLAC AS3193 Instrucciones De Uso

6 Plug it into the mains.
7 Turn on the vacuum by pressing the pedal
switch (3), and adjust the suction power by
opening or closing the regulator on the handle
(13). (The suction power is decreased by ope-
ning the valve, and it is increased by closing
the valve). You can also adjust the suction
power using the electronic regulator (6). Sli-
de the regulator between the MIN. and MAX.
positions, depending on the desired suction
power.
if you hear a sharp whistling sound that
is different from the normal sound when
using the vacuum, turn it off and unplug it.
check to see if the air inlets and outlets or
the filters are obstructed. If they are obs-
tructed, eliminate the cause.
When using the vacuum, pull it behind you as
if it were a cart. The handle (9) can also be
used to carry the vacuum cleaner.
This appliance has a position called the "ho-
rizontal parking" position, which can be con-
veniently used during stops while cleaning. To
put it in this position, insert the hook of the te-
lescopic tube in the groove (5) of the vacuum
cleaner body (Figure 1).
8 When finished, switch the appliance off by
pressing the On/Off button (3). Unplug it, and
press the button (8) to wind up the cord. Hold
the cord plug in your hand to prevent it from
banging against the vacuum cleaner housing.

cleAning And mAintenAnce

emptYing tHe duSt contAiner (10)

The dust container (10) has a maximum level
mark. Be sure that dirt does not exceed this
level.
The dust container has a container full indica-
tor light (15). Empty the dust container if this
light comes on. To do so:
1 Pull upwards on the handle (17) while pres-
sing the open button (16) (Figure 2).
2 Remove the dust container and hold it over
a rubbish bin. Press the release button (18),
and empty its contents into the rubbish bin (Fi-
gure 3).
3 Remove the cyclone filter (20) from the inte-
rior of the dust container by turning it coun-
ter-clockwise (Figure 4). Empty its contents,
rinse the filter with tap water, and be sure that
all washed elements are completely dry befo-
re installing them again.
AS3193_aspiradora.indd 12
4 Insert the cyclone filter in the container, and
turn it clockwise until the fastening tab is sea-
ted in the dust container (Figure 5).
5 To close the dust container, tilt the bottom co-
ver of the container (19), and press until you
hear a click, indicating that the cover is closed
correctly.
6 Place the dust container in the body of the
appliance. Press on the container until you
hear a click, which indicates that the container
is seated correctly (Figure 6).
The container full pilot light (15) may come on
at times if something becomes lodged in the
flexible tube, suction opening or accessory. To
find out if that is the case, unplug the vacuum
cleaner, remove the flexible tube, and turn
the vacuum cleaner on again. If the pilot light
does not come on, clean the flexible tube and
its attachment.
filter cleAning And replAcement
We recommend that you periodically
check the air filters to make sure that they
work correctly. Clean the filters if you de-
tect that the appliance's suction capacity
has decreased.
Clean the filters using tap water, and allow
them to dry completely. Do not use a hair dr-
yer to dry the filters.
It is advisable to replace the filters once or
twice a year, depending on how often the
appliance is used.
HEPa air outlet filter (7)
1 Remove the HEPA air outlet filter cover (4) by
pressing on the two buttons of the top (fig. 7).
2 Remove the HEPA outlet filter (7) from its hou-
sing to clean it.
3 Put the filter back in after it is clean.
4 Put the cover back in place. To do so, align the
tabs on the air outlet filter cover with the holes
located in the bottom of the vacuum cleaner;
press down on the filter cover until you hear a
click.
Never use the vacuum cleaner without the air
outlet filter.
Motor protection filter (14)
Empty the dust container before cleaning the
motor protector filter. See "Emptying the dust
container (10)".
1 Remove the dust container.
2 Remove the filter by pulling the top upward
(Figure 8).
en
23/5/16 15:53