Standard Accessories; Optional Accessories; Maintenance And Inspection - HIKOKI NH 18DSL Instrucciones De Manejo

STANDARD ACCESSORIES

WARNING
● Accessories other than those shown below can
lead to malfunction and resulting injuries.
1 Eye protection................1
NOTE: Accessories are subject to change without any
obligation on the part of HiKOKI.

OPTIONAL ACCESSORIES

(SOLD SEPARATELY)
1. Battery
○ BSL1815
2. Charger
○ UC18YKSL (Charging voltage: 14.4 V – 18 V)
Optional accessories are subject to change without notice.
APPLICATIONS
○ Wooden materials in general constructions, fi ttings,
wood decks, frameworks, and renovations
CHARGING
Battery and battery charger are not included with this
product.
For rechargeable batteries, please charge in according to
the handling instructions of the charger which you are using.
(Fig. 5)
MOUNTING AND OPERATION
Action
Inserting and removing the battery
Switch operation
Charging
Checking rod operations*
Shooting by holding a nail with the
magnet*
2
Shooting by holding a nail with
fi ngers.*
3
Fixing a nail to the metal joint
Using the hook*
5
Clearing a jam
Selecting accessories
Figure Page
3
4
5
6
1
7
8
9
*4
10
11
―
*1 WARNING
○ Check to make sure the rod slides smoothly when
operated. Clean the sliding area on the rod if it doesn't
slide smoothly.
*2 WARNING
○ When loading a nail in the rod, hold the nail shaft instead
of the tip.
○ When loading a nail in the rod, make sure it does not
press the tip of the driver unit.
○ When loading a nail in the rod, do not place your fi ngers
or hands below the tip of a nail.
*3 WARNING
○ When shooting a nail holding it with fi ngers, place the
nail tip at a target fi rst, and then insert the rod to the nail
head.
*4 WARNING
○ When shooting a nail, make sure the tip of the nail is in
the hole of the metal joint.
*5 CAUTION
○ When using the hook, hang up the power tool fi rmly not
to drop accidentally.
If the power tool is dropped, it may lead to an accident.
○ Make sure the battery removed when using the hook.
○ Install securely the hook. Unless the hook is securely
installed, it may cause an injury while using.
CAUTION
When shooting a nail, operate for a short time and avoid
continuous work. Otherwise may cause a failure or leak
grease.

MAINTENANCE AND INSPECTION

CAUTION
Be sure to remove battery from the Auto Hammer before
maintenance and inspection.
WARNING
○ Disconnect battery and remove nail from Auto Hammer
when:
1) doing maintenance and inspection; and
2) clearing a jam.
○ Without connecting the battery, check if the rod moves
steadily by pressing the rod tip against a material such
as of wood.
1. Clearing a jam (Fig. 11)
1 Remove battery from the Auto Hammer.
2 Remove the jammed nail with a pair of pliers.
3 In case of frequent jam, contact a HiKOKI authorized
service center.
2. Rod inspection (Fig. 6)
Periodically clean and lubricate the sliding part of the rod
and socket.
Check if the rod moves smoothly by pressing the Auto
Hammer against a material such as of wood.
When iron powders or the like adheres to the magnetized
2
area within the rod, the power to magnetically hold a nail
may be reduced. Wipe the area clean with a cloth or
2
adhesive tape sometimes.
3
Also, clean the iron powder on the magnet outside the
rod with cloth or adhesive tape sometimes.
3
It makes the rod operation smooth.
3. Inspecting the mounting screws
3
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
3
loose, retighten them immediately. Failure to do so could
result in serious hazard.
4
4. Maintenance of the motor
The motor unit winding is the very "heart" of the power
4
tool. Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
4
207
11
English