Festool DSC-AGC 18 FH Instrucciones De Uso Originales página 19

Specific safety warnings on sanding and abra­
sive cutting
– Use only wheel types that are recommen­
ded for your power tool and the specific
guard designed for the selected wheel.
Wheels for which the power tool was not
designed cannot be adequately guarded
and are unsafe.
The grinding surface of centre depressed
–
wheels must be mounted below the plane
of the guard lip. An improperly mounted
wheel that projects through the plane of
the guard lip cannot be adequately protec­
ted.
The guard must be securely attached to
–
the power tool and positioned for maxi­
mum safety, so the least amount of wheel
is exposed towards the operator. The
guard helps to protect the operator from
broken wheel fragments, accidental con­
tact with wheel and sparks that could ignite
clothing.
Wheels must be used only for recommen­
–
ded applications. For example: do not
grind with the side of cut-off wheel. Abra­
sive cut-off wheels are intended for periph­
eral grinding, side forces applied to these
wheels may cause them to shatter.
Always use undamaged wheel flanges that
–
are of correct size and shape for your se­
lected wheel. Proper wheel flanges sup­
port the wheel thus reducing the possibility
of wheel breakage. Flanges for cut-off
wheels may be different from grinding
wheel flanges.
– Do not use worn down wheels from larger
power tools. Wheel intended for larger
power tool is not suitable for the higher
speed of a smaller tool and may burst.
Other specific safety warnings on abrasive
cutting
Do not "jam" the cut-off wheel or apply
–
excessive pressure. Do not attempt to
make an excessive depth of cut. Over­
stressing the wheel increases the loading
and susceptibility to twisting or binding of
the wheel in the cut and the possibility of
kickback or wheel breakage.
– Do not position your body in line with and
behind the rotating wheel. When the
wheel, at the point of operation, is moving
away from your body, the possible kickback
may propel the spinning wheel and the
power tool directly at you.
When wheel is binding or when interrupt­
–
ing a cut for any reason, switch off the
power tool and hold the power tool mo­
tionless until the wheel comes to a com­
plete stop. Never attempt to remove the
cut-off wheel from the cut while the wheel
is in motion otherwise kickback may oc­
cur. Investigate and take corrective action
to eliminate the cause of wheel binding.
– Do not restart the cutting operation in the
workpiece. Let the wheel reach full speed
and carefully re-enter the cut. The wheel
may bind, walk up or kickback if the power
tool is restarted in the workpiece.
Support panels or any oversized work­
–
piece to minimize the risk of wheel pinch­
ing and kickback. Large workpieces tend to
sag under their own weight. Supports must
be placed under the workpiece near the
line of cut and near the edge of the work­
piece on both sides of the wheel.
– Use extra caution when making a "pocket
cut" into existing walls or other blind
areas. The protruding wheel may cut gas or
water pipes, electrical wiring or objects
that can cause kickback.
2.3 Further safety warnings
Do not use the power tool in the rain or in
–
damp surroundings. Moisture in the power
tool may cause a short circuit and burning.
– Only guide the power tool into the material
when it is switched on (running).
– For safety reasons, the workpiece must be
clamped in a vice or another type of clamp­
ing device. Clamping a workpiece frees up
both your hands for operating the power
tool.
– Never perform work while standing on lad­
ders.
– Do not use quick-action clamping nuts to
clamp the diamond cutting disc.
– Use suitable tools with corresponding
specifications for the material you are
working with – see information on the dia­
mond cutting disc and the packaging.
– Take a break after making multiple sepa­
rating cuts or after carrying out intensive
cutting tasks to allow the diamond cutting
disc to cool down and to prevent it from
overheating.
– Do not apply any pressure to the diamond
cutting disc from the side.
– Diamond cutting discs are self-sharpening.
A reduced cutting power and a circular, hot
edge indicate that a diamond cutting disc is
English
19