Electrical Safety; Replacing The Power Cable; Description And Package Contents; The Package Contains - Hurricane HVLI 1500 Instrucciones De Manejo

prescribed for the respective type of tool. You should
also consider the working conditions and the work to
be carried out.
• Have the power tool serviced by qualified technical
personnel only; repairs should be carried out using
exclusively original spare parts.
• Replace worn or damaged parts for reasons of safety.
Use only original spare parts. Parts not produced by
the original manufacturer may have a poor fit and
possibly cause injury.
• Grip guide bar firmly with both hands. Never operate
the tool with only one hand.
• Hold the guide bar and lift the tool to move it from
one place to another. Always switch off the tool, dis-
connect the plug and wait until the application stops
before carrying out maintenance.

Electrical safety

• The electric motor has been designed to use single
phase voltage only.
• Make sure your voltage corresponds to the one writ-
ten on the rating label.
Your machine has double insulation in
conformity to Directive EN 60335, you do
not therefore need to earth.
• Always use a plug compulsory for double insulation
electric tooling when replacing the cable.
• Always switch your machine off before disconnecting
any plug, socket or extension.
• Increased safety can be obtained by having a quali-
fied electrician install a high sensitivity (30mA) circuit
breaker in the house wiring. If you do not have such
a circuit breaker installed, or you do not wish to have
one installed, then we strongly recommend that the
electrical power to your Machine be supplied through
a high sensitivity (30mA) residual current device
(RCD). The RCD is designed to provide a high degree
of personal protection against harmful electric current
should fault conditions occur.
The use of an RCD or other circuit breaker
unit does not release the operator of your
Machine from the safety instructions
and safe working practices given in this
manual.
• When using an extension, make sure that it has been
certified and is the right size for conveying electric-
ity supply to the equipment (see technical specifica-
tions).
• Smallest size of lead is 1.5 mm². Completely unwind
the cable if you are using a winder.

Replacing the power cable

If the power cable of the device should be damaged it
must be replaced by the manufacturer or their after-sales
service or an equally qualified person to avoid any risks.

5. DESCRIPTION AND PACKAGE CONTENTS

The package contains (Fig. 1):
• 1 Machine body fitted with: lever to adjust height of
wheels (1), safety cover (2) and blade system of scari-
fier(3)
• 1 upper handle bar(4) fitted with: switch with cable and
switch release button (5), switch lever (6) and socket
to connect extension (7)
• 1 middle handle bar(8)
• 2 lower handle bars (9) fitted with: plastic holder (10)
and knobbed bolt(11)
• 2 cable clamps (12)
• 2 sets of winged nut and bolts (13) to fix middle handle
bar to lower handle bar
• 2 sets of knob nut and bolts(14) to fix upper handle bar
to middle handle bar
• 1 hook to hold extension (15)
• 1 set of grass bag(16)
• 1 set of blade system of lawn raker(17)
• 1 hexagon socket wrench (18) to change the blade
system
NOTE: make sure that the Machine and accessories in
the package are not damaged

6. ASSEMBLY AND SETTING UP

Always disconnect plug from mains before
assembly and setting up
HANDLE ASSEMBLY (Fig. 2)
• Insert the knobbed bolt of lower handle bar (9) from
outside in the two holes in the machine body and
screw the knobbed bolt to fix it (Fig. 2.1).
• Join the middle handle bar (8) to the lower handle bar
(9) by means of the winged nuts and bolts (13) pro-
vided (Fig. 2.2).
• Fit the cable hook (15) onto the upper handle bar from
the switch side (Fig. 2.3).
• Join the upper handle bar (4) to the middle handle bar
(8) by means of the knobbed nuts and bolts (14) pro-
vided ( Fig. 2.4).
• Fix the cable to the handle by the clamps (12) (Fig.
2.5).
GRASS BAG ASSEMBLY (Fig. 3)
• Insert the front metal frame into the rear metal frame
(Fig. 3.1).
• Fix the front metal frame inside the clamping rims of
cloth-bag (Fig. 3.2).
• Mount the grass collector bag as shown in the picture
(Fig. 3.3).
HEIGHT ADJUSTMENT (Fig. 4)
• Use the adjustment arm (1) of the machine body for
GB-6