Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
3.7. Adjusting the harness and headrest height in
an installation with a 5-point harness. Groups
0+/1
Proper adjustment of the height of the harness ensures
the child will be seated correctly. The harness should be
adjusted to the height of the child's shoulder or slightly
above; never behind the child's back or level with the
ears (fig. 7).
IMPORTANT! The shoulder straps should not be passed
behind the child's back at or above ear level.
1. Loosen the harness straps by pulling them gently
while pressing the harness adjustment button
(fig. 2).
2. Pull the headrest height adjuster
(9)
and the headrest
(1)
at the same time. Select the correct height for
the shoulder straps
(10)
and fix them in the correct
position for the child by releasing the adjuster (fig. 6).
3.8. Adjusting the headrest. Groups 2/3.
A correctly adjusted headrest ensures that the diagonal
part of the safety belt is ideally positioned, offering the
child the best possible protection.
The headrest should be adjusted so that a space
equivalent to two fingers remains between the headrest
and the child's shoulders.
To adjust the height of the headrest:
40
(9)
1. Pull the headrest height adjuster
and the headrest
at the same time. This will unlock the headrest (fig. 6).
2. now you will be able to move the headrest to the
desired height. when the adjuster is released the
headrest will remain locked in the chosen position.
3. Place the safety seat on the car seat.
4. Sit the child in the seat and check the height. Repeat
the process until the correct height is achieved.
Headrest and
(9)
fig. 6
harness height
(13)
adjuster.
fig. 7
4. CAR SEAT REARWARD-FACING INSTALLATION.
GROUP 0+/1
GROUP 0+/1. From 0 to 4
NOTICE
years approx. (0 - 18 kg).
NOTICE: It is advisable to use the seat backward-facing
as long as possible. If the height of the child or the size
of the vehicle prevents the child to travel rearward-facing
until 18kg, we advise to maintain rearward-facing travel
position up to 13 kg. If necessary, the seat can be installed
forward-facing when the child reaches 9kg of weight.
NOTICE: This car seat offers different installation options
(installation table, chapter 2) WITH or WITHOUT Isoclick
Fix
connectors.
®
• For a car seat installation using Isoclick Fix
connectors and vehicle's belt, please start from
section 4.1.
• For a car seat installation using only the vehicle´s belt,
please start from section 4.2.
fig. 8
(26)
Latch guide
(25)
ISoFIX securing
point
BNO FIX 0+123
www.babyqs.com
4.1 Connecting the Isoclick Fix
rearward-facing installation. Group 0+/1.
(optional)
• Preparing the Isoclick Fix system
1. If your vehicle has not been fitted with the ISOFIX latch
guides as standard, fit the two latch guides
came with the safety seat.
* With the opening facing upwards at the two ISOFIX
securing points
2. By turning, extract both Isoclick Fix arms (19). Move
the arms from side to side until you hear the click
indicating that they are fully locked (fig 9).
3. Make sure that the displayed arms corresponds to the
selected installation, group 0+/1 (rearward facing) or
®
group 1/2/3 (forward facing) (fig. 9).
(19)
Isoclick Fix
arms.
A
Group 1/2/3
installation.
26
B
Group 0+/1
installation.
25
arms in a
®
(26)
that
(25)
of your vehicle (fig.8).
®
fig. 9
A
B
19
41
41
Publicidad
Tabla de contenido
