Additional Safety Rules For Cordless Drills / Drivers - SPARKY HeavyDuty BR2 7.2Li HD Instrucciones De Uso

and balance at all times. This enables bet-
ter control of the power tool in unexpected
situations.
f) Dress properly. Do not wear loose cloth-
ing or jewellery. Keep your hair, cloth-
ing and gloves away from moving parts.
Loose clothes, jewellery or long hair can be
caught in moving parts.
g) If devices are provided for the connec-
tion of dust extraction and collection fa-
cilities, ensure these are connected and
properly used. Use of dust collection can
reduce dust-related hazards.
4. POWER TOOL USE AND CARE
a) Do not force the power tool. Use the cor-
rect power tool for your application. The
correct power tool will do the job better and
safer at the rate for which it was designed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power tool
that cannot be controlled with the switch is
dangerous and must be repaired.
c) Disconnect the plug from the power
source and/or the battery pack from the
power tool before making any adjust-
ments, changing accessories, or storing
power tools. Such preventive safety meas-
ures reduce the risk of starting the power tool
accidentally.
d) Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for misalign-
ment or binding of moving parts, break-
age of parts and any other condition that
may affect the power tool's operation. If
damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and tool
bits etc. in accordance with these in-
structions, taking into account the work-
ing conditions and the work to be per-
formed. Use of the power tool for operations
different from those intended could result in
a hazardous situation.
Original instructions
pages BR2-7.2LiHD.indd 5
5. SERVICE
a) Have your power tool serviced by a quali-
fied repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
IV - Additional safety
rules for cordless
drills / drivers
▪ Be aware that this tool is always in operat-
ing condition, because it does not have to be
plugged into an electrical outlet. Always set the
trigger switch to the locked OFF position when
installing or removing the battery pack.
▪ If possible, always use clamps or a vice to hold
your work.
▪ Do not touch the bit after operation. It will be
very hot.
▪ When using the drill, use safety equipment
including safety glasses and ear defenders.
Wear a dust mask if the drilling operation cre-
ates dust.
▪ The dust, separated while processing materi-
als, containing quartz (SiO
your health. Do not process materials contain-
ing asbestos.
▪ The tool must be used only for its prescribed
purpose. Any use other than those mentioned
in this Manual will be considered a case of mis-
use. The user and not the manufacturer shall
be liable for any damage or injury resulting from
such cases of misuse.
▪ To use this tool properly, you must observe the
safety regulations, the assembly instructions
and the operating instructions to be found in
this Manual. All persons who use and service
the machine have to be acquainted with this
Manual and must be informed about its poten-
tial hazards. Children and frail people must not
use this tool. Children should be supervised
at all times if they are in the area in which the
tool is being used. It is also imperative that you
observe the accident prevention regulations in
force in your area. The same applies for gen-
eral rules of occupational health and safety.
▪ The manufacturer shall not be liable for any
changes made to the tool nor for any damage
resulting from such changes.
Even when the tool is used as prescribed it is not
possible to eliminate all residual risk factors. The
following hazards may arise in connection with
the tool's construction and design:
) is dangerous to
2
5
EN
9.11.2011 . 09:43:13 .