Technical Delivery; Start Procedure - Schulz SRP 3040E Manual De Instrucciones

SCREW AIR COMPRESSOR

TECHNICAL DELIVERY

After all the compressor is installed and connected as per the customers requirements, the compressor must be
started in the presence of a representative of the nearest
technician will validate the Warranty as required by SCHULZ and will guide the customer on starting
procedures, and provide owner/operator training in the compressor's operation and preventive maintenance.
The compressor's warranty will be validated and the warranty period initiated only a) upon production of the
Technical Delivery report provided by
- one copy of which will remain with the customer and b) the filling in of the Technical Delivery Log (page 65)
which will be sent to the factory by the technician. Instructions contained in item "A" of the Warranty Terms (page
102), under General Warranty Conditions, must be followed.

START PROCEDURE

SRP 3,000 series compressors are tested in the factory and supplied with mineral lubricant oil
Before the compressor's initial start, check the belt's strain (Figure 15, page 52), re-fasten the
connections of the hydraulic circuit hoses and of the electric contacts.
FIRST START PROCEDURE - SRP 3040E COMPRESSOR'S:
A. Open the cabinet's left side door (facing the panel) and check the oil level; with must be at the maximum
level of the oil level sight (item
B. If the ambient temperature is different from (Table 3, page 53) specifications, change to screw compressor
lubricant oil ISO 32
C. Indicator light (item
energized;
D. The display must show the working pressure and it must not be flashing;
E. Close the air outlet valve;
F. Check Rotation by pressing the Start Key (
the emergency stop (
must be in the direction indicated by the arrow located in the air end casting. The correct air flow is toward the
cooler.
Notes: If the rotation is incorrect, disconnect input power from the compressor and interchange two wires at
the disconnect, to reverse fan direction, interchange two (2) wires at contactor K4 and repeat procedure .
Unlock the emergency button and press the "reset key" in the Electronic Interface to cancel message
the display, which will later show item
G. After making sure that the rotation direction is correct, close the side door and press the Start Key
to run the compressor again, keeping the valve closed until the compressor reaches its maximum pressure
and starts to unload
compressed air to the network.
FIRST START PROCEDURE - SRP 3040 COMPRESSOR'S:
A. Open the cabinet's left side door (facing the panel) and check the oil level; the oil level sight (item
17, page 53) must be covered;
If the ambient temperature is different from (Table 3, page 53) specifications, change to screw compressor
B.
lubricant oil ISO 32
C. Indicator light (item
energized;
D. Close the air outlet valve;
E. Check Rotation by pressing the Start Key (
the emergency stop (
must be in the direction indicated by the arrow located in the air end casting. The correct air flow is toward the
cooler.
Notes: If the rotation is incorrect, disconnect input power from the compressor and interchange two wires at
the disconnect, to reverse fan direction, interchange two (2) wires at contactor K5 and repeat procedure .
Unlock the emergency button.
50
SCHULZ Authorized - Technical/Distributor
3, Figure 17, page 53);
.
2, Figure 11, page 46) of the instrument panel must be on showing that the controls are
red ) button, switching the compressor off and observing the direction of rotation. It
D's characteristics.
(ALI) . Slowly open the valve and your rotary screw air compressor is now ready to supply
.
8, Figure 12, page 47) of the instrument panel must be on showing that the controls are
red ) button, switching the compressor off and observing the direction of rotation. It
SCHULZ Authorized - Technical/Distributor
green ) to switch on the compressor and immediately pressing
green ) to switch on the compressor and immediately pressing
SRP 3040E - SRP 3040
during the first start procedure
ISO 46.
(green)
3,
. This
F
P03 on
Figure
E