Stiga PARK FKM 900 KA Instrucciones De Uso página 37

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 58
M - Steering bush
N - Bush
O - Tightening lever
P - Pulley
Q - Drive belt 6898
R - Drive belt 6871
6.2 INSTALLING THE PULLEY (2)
E – Drive belt guard
P – Pulley
S – Threaded pin M6x10
X – Adjustment spring
T – Hexagon screw M6x20
U – Spring washer M6
V – Washer M6
W – Stop nut M6
6.3 INSTALLING THE CROSS
MEMBER (4)
T – Hexagon screw M8x30
V – Washer M8
W – Stop nut M8
6.4 INSTALLING THE RIGHT DECK
ARM (5)
G – Right deck arm
T – Screw with locking teeth M10x35
Z – Bodywork washer M10
K – Bearing bush
W – Stop nut M10
6.5 INSTALLING THE LEFT DECK
ARM (6)
H – Left deck arm
T – Screw with locking teeth M10x30
Z – Bodywork washer M10
K – Bearing bush
6.6 INSTALLING THE
ADJUSTMENT SUPPORT (7)
J – Adjustment support
G – Right deck arm
T – Hexagon screw M10x65
Z – Bodywork washer M10
V – Washer M10
Y – Narrow hexagon nut M10
N – Bush 9.5 long
6.7 INSTALLING THE LIFT (8)
L – Adjustment notch
Z – Bodywork washer M10
V – Washer M10
W – Stop nut M10
U – Spring washer M10
C – Wing screw M10x35
ENGELSKA
D – Lift on Stiga
E –Tightening lever
B – Hexagon screw M6x10
N – Steering bush
6.8 INSTALLING FKM 900 KA (9)
• Attachment must be correctly carried out to
avoid injury both to the user and to third parties.
• Switch off the engine of the ride-on lawn
mower and remove the ignition key before the
sweeping deck is attached or removed.
• Position the sweeping deck with the right deck
arm (9:C) and the left deck arm in the machine's
quick release mountings.
Then put the drive belt on, lock the quick release
(9:A) and insert a locking pin (9:B).
Warning! Risk of crushing injuries!
• Two side supports (extra accessories) are
recommended as support when attaching and
removing the sweeping deck
6.9 INSTALLATION OF DIRT
COLLECTOR
• Screw both guide rails into place (10:C) at the
front on the right and left of the sweeping deck
housing (10:A) with two screws and nuts on
each side (10:T Z).
• Fold the locking lever for the collector (10:H).
• Then hook the lock bar into both guide rails on
the left and right sides of the deck housing.
• Pull the lock bar (10:H) down and place it in the
bar holder.
• Continuous adjustment is required depending
on how much the sweeper roller wears.
Other details in the figure (10)
B - Dirt collector
D - Height scale - bar holder
H - Lock lever - open/hook in
F - Twist handle
6.10 INSTALLING THE SIDE BRUSH
(11)
• The first time that the brush is installed the
tension bar (11:S) on the right side is withdrawn
from the sweeping deck (11:A) and the existing
bodywork washer replaced by the spring
washer (11:U) and pulley (11:P) supplied. Slide
everything into the sweeping deck.
• Screw the mounting plate (11:R) on the right
side panel using four screws, spring washers
and nuts (see 4 x 11:"A"). Attach the front side
brush arm on the mounting plate arm at "B"
with screws M10 x 50 mm, washer and stop
nuts.
EN
37

Publicidad

Tabla de contenido
loading

Tabla de contenido