Fein AGSZ18-280BL Manual De Instrucciones página 21

OBJ_BUCH-0000000285-001.book Page 21 Monday, February 19, 2018 10:27 AM
AGSZ18-90 LBL: Operation as sanding are not recom-
mended to be performed with this power tool. Operations
for which the power tool was not designed may create a
hazard and cause personal injury.
Do not use accessories which are not specifically
designed and recommended by the tool manufacturer.
Just because the accessory can be attached to your power
tool, it does not assure safe operation.
The rated speed of the accessory must be at least equal
to the maximum speed marked on the power tool. Acces-
sories running faster than their rated speed can break and
fly apart.
The outside diameter and the thickness of your accessory
must be within the capacity rating of your power tool.
Incorrectly sized accessories cannot be adequately
guarded or controlled.
Grinding wheels, sanding drums or other accessories
must exactly fit the grinder spindle or collet of your
power tool. Application tools that do not fit exactly in the
tool holder of the power tool will run out of balance,
vibrate excessively and may cause loss of control.
Grinding wheels, sanding drums or cutting tools mounted
on a mandrel, or other accessories must be fully inserted
into the collet or chuck. The "projecting end" as well as
the free part of the mandrel between the grinding acces-
sory and the collet/chuck must be minimal. If the mandrel
is insufficiently clamped or if the overhang of the grinding
accessory is too long, the application tool may become
loose and ejected at high velocity.
Do not use damaged application tools. Before each use,
check application tools such as grinding wheels for chips
and cracks, sanding drums for cracks, wear or heavy use,
and wire brushes for loose or broken wires. If the
machine or application tool is dropped, inspect for dam-
age or install an undamaged application tool. After
inspecting and installing the application tool, position
yourself and bystanders away from the plane of the rotat-
ing application tool and run the machine at maximum no-
load speed for one minute. Damaged application tools will
normally break apart during this test time.
Wear personal protective equipment. Depending on appli-
cation, use face shield, safety goggles or safety glasses.
Where appropriate, wear dust mask, hearing protectors,
gloves and workshop apron capable of stopping small
abrasive or workpiece fragments. The eye protection
must be capable of stopping flying debris generated by
various operations. The dust mask or respirator must be
capable of filtrating particles generated by your opera-
tion. Prolonged exposure to high intensity noise may
cause hearing loss.
Keep bystanders a safe distance away from work area.
Anyone entering the work area must wear personal pro-
tective equipment. Fragments of workpiece or of a bro-
ken accessory may fly away and cause injury beyond
immediate area of operation.
Hold the power tool by insulated gripping surfaces only,
when performing an operation where the cutting acces-
sory may contact hidden wiring. Cutting accessory con-
tacting a "live" wire may make exposed metal parts of the
power tool "live" and could give the operator an electric
shock.
Always hold the power tool firmly when starting it. The
reaction torque of the motor, as it accelerates to full
speed, can cause the power tool to twist.
If possible, use clamps to fasten or affix the workpiece.
Never hold a small workpiece in one hand and the power
tool in the other hand while in use. Clamping small work-
pieces allows you to use both hands for better control
the power tool. Round material such as dowel rods, pipes
or tubing have a tendency to roll away while being cut,
and may cause the application tool to jam or bind and be
thrown toward you.
Never lay the power tool down until the accessory has
come to a complete stop. The spinning accessory may
grab the surface and pull the power tool out of your con-
trol.
After changing application tools or making adjustments
on the tool, tighten the collet nut, chuck or any other fas-
tening elements. Loose fastening elements can unexpect-
edly misadjust and lead to loss of control; unfastened,
rotating components will be violently thrown.
Do not run the power tool while carrying it at your side.
Accidental contact with the spinning accessory could snag
your clothing, pulling the accessory into your body.
Regularly clean the power tool's air vents. The motor's
fan will draw the dust inside the housing and excessive
accumulation of powdered metal may cause electrical
hazards.
Do not operate the power tool near flammable materials.
Sparks could ignite these materials.
Do not use accessories that require liquid coolants. Using
water or other liquid coolants may result in electrocution
or shock.
Further safety warnings for all applications
Kickback and related warnings
Kickback is the sudden reaction to a pinched or snagged
rotating application tool, such as a grinding wheel, sand-
ing belt, wire brush, etc. Pinching or snagging causes the
rotating application tool to rapidly stop. This causes an
uncontrolled power tool to be forced in the direction
opposite of the application tool's rotation direction.
For example, if a grinding wheel is snagged or pinched in
the workpiece, the edge of the grinding wheel that is
entering into the workpiece can be caught, causing the
grinding wheel to break out or cause kickback. The grind-
ing wheel may either jump toward or away from the
operator, depending on the direction of the wheel at the
point of blocking. Grinding wheels can also break under
these conditions.
Kickback is the result of power tool misuse or incorrect
operating procedures. It can be avoided by taking proper
precautions as described below.
en
21