Dremel 8220 Manual De Instrucciones página 20

SAFETY WARNINGS SPECIFIC FOR
SANDING OPERATIONS
a. Do not use excessively oversized sanding disc paper.
Follow manufacturers recommendations, when selecting
sanding paper. Larger sanding paper extending beyond the
sanding pad presents a laceration hazard and may cause
snagging, tearing of the disc or kickback.
SAFETY WARNINGS SPECIFIC FOR
POLISHING OPERATIONS
a. Do not allow any loose portion of the polishing bonnet
or its attachment strings to spin freely. Tuck away or
trim any loose attachment strings. Loose and spinning
attachment strings can entangle your fingers or snag on the
workpiece.
SAFETY WARNINGS SPECIFIC FOR
WIRE BRUSHING OPERATIONS
a. Be aware that wire bristles are thrown by the brush
even during ordinary operation. Do not overstress the
wires by applying excessive load to the brush. The wire
bristles can easily penetrate light clothing and/or skin.
b. Allow brushes to run at operating speed for at least one
minute before using them. During this time no one is to
stand in front or in line with the brush. Loose bristles or
wires will be discharged during the run-in time.
c. Direct the discharge of the spinning wire brush away
from you. Small particles and tiny wire fragments may be
discharged at high velocity during the use of these brushes
and may become imbedded in your skin.
d. If the use of a guard is recommended for wire brushing,
do not allow any interference of the wire wheel or
brush with the guard. Wire wheel or brush may expand in
diameter due to work load and centrifugal forces.
–1
e. Do not exceed 15000 min when using wire brushes.
Do not work with materials containing
WARNING
!
asbestos (asbestos is considered
carcinogenic).
Take protective measures when during
WARNING
!
work dust can develop that is harmful
to one's health, combustible or explosive (some dusts
are considered carcinogenic); wear a dust mask and
work with dust/ chip extraction when connectable.
ENVIRONMENT
DISPOSAL
The machine, accessories and packaging should be sorted for
environmental-friendly recycling.
2610034063-8220AUS-LAM.indb 20
ONLY FOR EUROPEAN COUNTRIES
Do not dispose of power tools into household waste!
According the European Guideline 2002/96/EC for
Waste Electrical and Electronic Equipment and its
implementation into national right, power tools that are
no longer usable must be collected separately and
disposed of in an environmentally correct manner.
SPECIFICATIONS
GENERAL SPECIFICATIONS
Voltage Rating . . . . . . . . . . . 10,8 V
Amperage Rating . . . . . . . . . 1,3 – 2,0 Ah
No Load Speed . . . . . . . . . . . n
Collet Capacity . . . . . . . . . . . 0,8 mm, 1,6 mm, 2,4 mm, 3,2 mm
SPECIFICATIONS CHARGER
Input . . . . . . . . . . . . . . . . . . . 230 – 240 V, 50 – 60 Hz, 26 W
Output . . . . . . . . . . . . . . . . . 3,6 V - 10,8 V , 1,5 A
EXTENSION CORDS
Use completely unrolled and safe extension cords with a
capacity of 5 Amps.
ALWAYS TURN OFF THE TOOL BEFORE CHANGING ACCESSORIES,
CHANGING COLLETS, OR SERVICING THE TOOL.
BATTERY CHARGE CONDITION INDICATOR
Your tool is equipped with charge condition indicator lights
(picture 1 D). The indicator lights shows the charge condition of
the battery.
3 of 3 Solid LED's = 67-100%
2 of 3 Solid LED's = 34-66%
1 of 3 Solid LED's = 16-33%
1 of 3 Flashing LED's = 0-15%
3 "side to side" lights – battery charge is too low to run tool.
Recharge the battery.
3 "flashing" lights – battery is too hot for use. Turn tool off and
let battery cool down.
Your tool is equipped with advanced electronics that protect
the Li-Ion cells in the battery from damage due to excessive
operating temperature and/or current draw. If the warning
symbol illuminates red and/or the tool stops working during
heavy use, this most likely indicates that the Li-Ion cells are
near their maximum operating temperature, and the battery
pack should either be changed or allowed to cool to ambient
temperature before continuing use. If the tool automatically turns
off due to overload conditions, the switch must be turned off for
a few seconds to allow the circuit to reset before continuing use.
20
DV-2610034063, Page: MUL (VAC), downloaded at: 2016.05.13_09:04:39, by PT-RT/MKT-AP_Echo.ZHANG
–1
5000 – 30000 min
o
ASSEMBLY
LIGHTS
6/26/14 1:32 PM