Bevel Cut; Compound Cutting - Makita DLS110 Manual De Instrucciones

Bevel cut

WARNING:
After setting the blade for a bevel
cut, ensure that the carriage and blade will have
free travel throughout the entire range of the
intended cut before operating the tool. Interruption
of the carriage or blade travel during the cutting oper-
ation may result in kickback and serious personal
injury.
WARNING:
While making a bevel cut keep
hands out of the path of the blade. The angle of the
blade may confuse the operator as to the actual blade
path while cutting and contact with the blade will
result in serious personal injury
WARNING:
The blade should not be raised
until it has come to a complete stop. During a
bevel cut the piece cut off may come to rest against
the blade. If the blade is raised while it is rotating the
cut-off piece maybe ejected by the blade causing
the material to fragment which may result in serious
personal injury.
NOTICE:
When pressing down the handle, apply
pressure in parallel with the blade. If a force is
applied perpendicularly to the turn base or if the pres-
sure direction is changed during a cut, the precision
of the cut will be impaired.
► Fig.49
1. Remove the upper fence on the side that you are
going to tilt the carriage.
2. Unlock the stopper pin.
3. Adjust the bevel angle according to the procedure
explained in the "Adjusting the bevel angle" section.
Then tighten the knob.
4.
Secure the workpiece with a vise.
5. Pull the carriage toward you fully.
6. Switch on the tool without the blade making any
contact and wait until the blade attains full speed.
7. Gently lower the handle to the fully lowered posi-
tion while applying pressure in parallel with the blade
and push the carriage toward the guide fence to cut
the workpiece.
8. When the cut is completed, switch off the tool and
wait until the blade has come to a complete stop
before returning the blade to its fully elevated position.

Compound cutting

Compound cutting is the process in which a bevel
angle is made at the same time in which a miter angle
is being cut on a workpiece. Compound cutting can be
performed at the angle shown in the table.
Miter angle
Left and Right 0° - 45°
When performing compound cutting, refer to "Press cut-
ting", "Slide (push) cutting", "Miter cutting" and "Bevel
cut" explanations
Bevel angle
Left and Right 0° - 45°
28 ENGLISH
Cutting crown and cove moldings
Crown and cove moldings can be cut on a compound
miter saw with the moldings laid flat on the turn base.
There are two common types of crown moldings and
one type of cove moldings; 52/38° wall angle crown
molding, 45° wall angle crown molding and 45° wall
angle cove molding.
► Fig.50: 1. 52/38° type crown molding 2. 45° type
crown molding 3. 45° type cove molding
There are crown and cove molding joints which are
made to fit "Inside" 90° corners ((a) and (b) in the figure)
and "Outside" 90° corners ((c) and (d) in the figure.)
(a) (b)
1. Inside corner 2. Outside corner
1
(b)
(a)
(b)
(a)
1. Inside corner 2. Outside corner
Measuring
Measure the wall width, and adjust the width of the
workpiece according to it. Always make sure that width
of the workpiece's wall contact edge is the same as wall
length.
► Fig.51: 1. Workpiece 2. Wall width 3. Width of the
workpiece 4. Wall contact edge
Always use several pieces for test cuts to check the
saw angles.
When cutting crown and cove moldings, set the bevel
angle and miter angle as indicated in the table (A) and
position the moldings on the top surface of the saw
base as indicated in the table (B).
(c) (d)
1 2
(b) (a)
(a)
(b)
(d)
(c)
(a)
(b)
2