Bevel Cut; Compound Cutting - Makita DLS110 Manual De Instrucciones

Bevel cut

WARNING:
After setting the blade for a bevel
cut, ensure that the carriage and blade will have
free travel throughout the entire range of the
intended cut before operating the tool. Interruption
of the carriage or blade travel during the cutting oper-
ation may result in kickback and serious personal
LQMXU\
WARNING:
While making a bevel cut keep
hands out of the path of the blade. 7KH DQJOH RI WKH
blade may confuse the operator as to the actual blade
path while cutting and contact with the blade will
UHVXOW LQ VHULRXV SHUVRQDO LQMXU\
WARNING:
The blade should not be raised
until it has come to a complete stop. During a
bevel cut the piece cut off may come to rest against
the blade. If the blade is raised while it is rotating the
FXWRII SLHFH PD\EH HMHFWHG E\ WKH EODGH FDXVLQJ
the material to fragment which may result in serious
SHUVRQDO LQMXU\
NOTICE:
When pressing down the handle, apply
pressure in parallel with the blade. If a force is
applied perpendicularly to the turn base or if the pres-
sure direction is changed during a cut, the precision
of the cut will be impaired.
Fig.49
1. Remove the upper fence on the side that you are
going to tilt the carriage.
2. Unlock the stopper pin.
3. $GMXVW WKH EHYHO DQJOH DFFRUGLQJ WR WKH SURFHGXUH
H[SODLQHG LQ WKH $GMXVWLQJ WKH EHYHO DQJOH VHFWLRQ
7KHQ WLJKWHQ WKH NQRE
4. Secure the workpiece with a vise.
5. Pull the carriage toward you fully.
6. Switch on the tool without the blade making any
contact and wait until the blade attains full speed.
7. Gently lower the handle to the fully lowered posi-
tion while applying pressure in parallel with the blade
and push the carriage toward the guide fence to cut
the workpiece.
8. When the cut is completed, switch off the tool and
wait until the blade has come to a complete stop
before returning the blade to its fully elevated position.

Compound cutting

Compound cutting is the process in which a bevel
angle is made at the same time in which a miter angle
is being cut on a workpiece. Compound cutting can be
performed at the angle shown in the table.
Miter angle
Left and Right 0° - 45°
:KHQ SHUIRUPLQJ FRPSRXQG FXWWLQJ UHIHU WR 3UHVV FXW-
WLQJ  6OLGH SXVK FXWWLQJ  0LWHU FXWWLQJ DQG %HYHO
FXW H[SODQDWLRQV
Bevel angle
Left and Right 0° - 45°
28 ENGLISH
Cutting crown and cove moldings
Crown and cove moldings can be cut on a compound
PLWHU VDZ ZLWK WKH PROGLQJV ODLG ÀDW RQ WKH WXUQ EDVH
7KHUH DUH WZR FRPPRQ W\SHV RI FURZQ PROGLQJV DQG
RQH W\SH RI FRYH PROGLQJV ƒ ZDOO DQJOH FURZQ
molding, 45° wall angle crown molding and 45° wall
angle cove molding.
Fig.50: 1. ƒ W\SH FURZQ PROGLQJ 2. 45° type
crown molding 3. 45° type cove molding
7KHUH DUH FURZQ DQG FRYH PROGLQJ MRLQWV ZKLFK DUH
PDGH WR ¿W ,QVLGH ƒ FRUQHUV D DQG E LQ WKH ¿JXUH
DQG 2XWVLGH ƒ FRUQHUV F DQG G LQ WKH ¿JXUH
(a) (b)
1
1. Inside corner 2. Outside corner
1
(b)
(a)
(b)
(a)
1. Inside corner 2. Outside corner
Measuring
0HDVXUH WKH ZDOO ZLGWK DQG DGMXVW WKH ZLGWK RI WKH
ZRUNSLHFH DFFRUGLQJ WR LW $OZD\V PDNH VXUH WKDW ZLGWK
of the workpiece's wall contact edge is the same as wall
length.
Fig.51: 1. Workpiece 2. Wall width 3. Width of the
workpiece 4. Wall contact edge
$OZD\V XVH VHYHUDO SLHFHV IRU WHVW FXWV WR FKHFN WKH
saw angles.
When cutting crown and cove moldings, set the bevel
DQJOH DQG PLWHU DQJOH DV LQGLFDWHG LQ WKH WDEOH $ DQG
position the moldings on the top surface of the saw
base as indicated in the table (B).
(c) (d)
2
(a)
(b)
(a)
(b)
(d)
2
(c)
(a)
(b)