Denon DN-D4500 Instrucciones De Operación página 9

!9
FLIP/B TRIM button
• Push this button to switch between the loop
mode/hot start mode and stutter mode.
• After setting the B point, the B TRIM MODE
can be selected.
@0
A1, A2 buttons
• Push these buttons to set the start point for
loop playback (point A-1 or A-2).
• Push these buttons to use the stutter and hot
start functions.
@1
B button
• Push this button to set the end point for loop
playback (point B).
@2
EXIT/RELOOP button
• When this button is pushed during a seamless
loop, the track resumes back to normal play
from the B point. (EXIT)
When pushed again, the playback jumps back
into your A-B seamless loop. (RELOOP)
@3
TITLE button
• CD TEXT:
When there is CD text data, the CD text data is
displayed automatically or when the button is
pressed.
If no TEXT is available, the display will indicate
"No TEXT".
• MP3:
When an MP3 file has ID-3 tag data, the title,
artist name and album name can be selected
and displayed each time the button is pressed.
@4
MEMO, PRESET button
• MEMO:
The memo mode starts when this button is
pushed once in the CUE mode.
• PRESET:
When this button is pushed for more than 1
sec, the PRESET mode starts.
NOTE:
• Memo's can not be set for MP3 files.
(3) DN-D4500 Rear panel
@5
Analog output jacks 1, 2
(ANALOG OUT 1, 2)
• These are unbalanced output jacks. The audio
signals from the both players are output from
these jacks.
@6
Digital output jacks 1, 2
(DIGITAL OUT 1, 2)
• Digital data is available from this jack.
• Use 75 Ω/ohms pin cord for connection.
• We recommend you use braided wire type
shielded cable.
NOTE: The playback level after analog
conversion is set to –6dB bellow the
usual level to avoid digital distortion.
@7
Fader input jacks 1, 2 (FADER 1, 2)
• Use this when your mixer has Fader Start
function with 3.5 mm stereo mini cord.
@8
Remote control connector
(REMOTE)
• Connect the supplied 8pin din cable to the
RC-D45 control unit.
(4) RC-D45 Rear panel
@9
Control connector
• Connect the opposite side of supplied 8pin din
cable to the DN-D4500 (main unit).
(5) Display
!0 w i
u q e
q
Track, minute, second and frame
displays
• These displays indicate current position
information.
w
Loop mode indicat ors
• DN-D4500 has Loop mode indicators consist of
two sets of A (A1, A2), B and two arrows. A
and B marks indicate A and B points are set.
• Two arrows indicate loop setting mode as
follows.
Example: A1 B
A1 B Both arrows on:
Seamless Loop mode
A1 B , A1 B Both arrows flashing:
Seamless Loop Playing
A1 B A1 B Left arrow on, right flashing:
,
Exit play from Seamless Loop
e
Time mode indicators
• When the TIME/TOTAL button is pushed, the
Time mode indicator switches as follows:
ELAPSED:
Track's elapsed time is displayed.
REMAIN:
Track's remaining time is displayed.
T. + ELAPSED:
The total elapsed time of disc
programmed track is displayed.
T. + REMAIN:
The total remaining time of disc or
programmed track is displayed.
t r
y o
r
MP3 file search mode indicator
FILE:
FILE indicator appears in display, when in
the FILE name search mode.
FOLDER:
FOLDER indicator appears in display, when
in the FILE & FOLDER name search mode.
TITLE:
TITLE indicator appears in display, when in
the TITLE name search mode.
ARTIST:
ARTIST indicator appears in display, when in
the ARTIST name search mode.
t
Character display
• This displays various operational information,
text message, etc.
y
Play mode indicators
• When SINGLE indicator lights up, playback will
finish at end of current track.
• When CONT. indicator lights up, playback
continues to the end of the disc.
u
MEMO indicator
• MEMO sign appears in display when there is a
memory setting for the currently playing track
or the track at which the standby mode is
currently set.
or
ENGLISH
9