Noise And Vibration Information - Festool POLLUX 180 E Manual De Instrucciones

i) Keep bystanders a safe distance away from
work area. Anyone entering the work area
must wear personal protective equipment.
Fragments of workpiece or of a broken ac-
cessory may fl y away and cause injury beyond
immediate area of operation.
j) Position the cord clear of the spinning acces-
sory. If you lose control, the cord may be cut or
snagged and your hand or arm may be pulled
into the spinning accessory.
k) Never lay the power tool down until the acces-
sory has come to a complete stop. Accidental
contact with the spinning accessory could snag
your clothing, pulling the accessory into your
body.
l) Do not run the power tool while carrying it at
your side. Accidental contact with the spinning
accessory could snag your clothing, pulling the
accessory into your body.
m) Regularly clean the power tool's air vents.
The motor's fan will draw the dust inside the
housing and excessive accumulation of pow-
dered metal may cause electrical hazards.
n) Do not operate the power tool near flam-
mable materials. Sparks could ignite these
materials.
o) Do not use accessories that require liquid
coolants. Using water or other liquid coolants
may result in electrocution or shock.
p) Only for AS/NZS: The tool shall always be sup-
plied via residual current device with a rated
residual current of 30 mA or less.
Kickback and Related Warnings
Kickback is a sudden reaction to a pinched or
snagged rotating wheel, backing pad, brush or
any other accessory. Pinching or snagging causes
rapid stalling of the rotating accessory which in
turn causes the uncontrolled power tool to be
forced in the direction opposite of the accessory's
rotation at the point of the binding.
For example, if an abrasive wheel is snagged or
pinched by the workpiece, the edge of the wheel
that is entering into the pinch point can dig into
the surface of the material causing the wheel to
climb out or kick out. The wheel may either jump
toward or away from the operator, depending on
direction of the wheel's movement at the point of
pinching. Abrasive wheels may also break under
these conditions. Kickback is the result of power
tool misuse and/or incorrect operating proce-
dures or conditions and can be avoided by taking
proper precautions as given below.
a) Maintain a fi rm grip on the power tool and
position your body and arm to allow you to
resist kickback forces. Always use auxiliary
handle, if provided, for maximum control over
kickback or torque reaction during start-up.
The operator can control torque reactions
or kickback forces, if proper precautions are
taken.
b) Never place your hand near the rotating ac-
cessory. Accessory may kickback over your
hand.
c) Do not position your body in the area where
power tool will move if kickback occurs. Kick-
back will propel the tool in direction opposite to
the wheel's movement at the point of snagging.
d) Use special care when working corners, sharp
edges etc. Avoid bouncing and snagging the
accessory. Corners, sharp edges or bouncing
have a tendency to snag the rotating accessory
and cause loss of control or kickback.
e) Do not attach a saw chain woodcarving blade
or toothed saw blade. Such blades create
frequent kickback and loss of control.
Safety Warnings Specifi c for Polishing Opera-
tions
a) Do not allow any loose portion of the polishing
bonnet or its attachment strings to spin free-
ly. Tuck away or trim any loose attachment
strings. Loose and spinning attachment
strings can entangle your fi ngers or snag on
the workpiece.
b) Prevent the penetration of liquid polish into
the tool. The penetration of liquid polish into
the power tool increases the risk of an electric
shock.
2.3

Noise and vibration information

The typical values determined in accordance with
EN 60745 are:
Sound pressure level
Noise power level
Measuring uncertainty allowance
CAUTION
The noise produced during work can damage
your hearing.
 Always use ear protection.
Vibration emission value a
directions) and uncertainty K measured in accord-
ance with EN 60745:
Polishing:
The specifi ed emissions values (vibration, noise)
11
89 dB(A)
100 dB(A)
K = 3 dB
(vector sum for three
h
a < 2,5 m/s
h
K = 2,0 m/s
2
2