Engine Oil; Air Cleaner - Honda GC160 Manual Del Proprietário

Never use stale or contaminated gasoline or oil/gasoline mixture.
Avoid getting dirt or water in the fuel tank.
 WARNING
Gasoline is highly flammable and explosive.
You can be burned or seriously injured when handling fuel.
• Stop the engine and allow to cool.
• Keep heat, sparks, and flame away.
• Handle fuel only outdoors.
• Wipe up spills immediately.
Adding Fuel
See Figure 7, page 3.
1. Remove the fuel tank cap.
2. Add fuel to the bottom of the fuel level limit [1] in the neck of the
fuel tank. Do not overfill. Wipe up spilled fuel before starting the
engine.
3. Install the fuel tank cap and tighten it until it clicks.
Move at least 10 feet (3 meters) away from the fueling source and
site before starting the engine.
NOTICE
Fuel can damage paint and some types of plastic. Be careful not to
spill fuel when filling your fuel tank. Damage caused by spilled fuel is
not covered under your DISTRIBUTOR'S LIMITED WARRANTY.

ENGINE OIL

Oil is a major factor affecting performance and service life. Always
change the oil in accordance with the maintenance schedule
(page 6).
Recommended Oil
See Figure 8, page 3.
Use 4-stroke motor oil that meets or exceeds the requirements for API
service category SJ or later. Always check the API service label on
the oil container to be sure it includes the letters SJ or later.
SAE 10W-30 is recommended for general use. Other viscosities
shown in the chart may be used when the average temperature in
your area is within the indicated range.
Oil Level Check
See Figure 8, page 3.
1. Check the oil with the engine stopped and level.
2. Remove the oil filler cap/dipstick [1] and wipe it clean.
3. Insert the oil filler cap/dipstick into the oil filler neck as shown, but
do not screw it in, and then remove it to check the oil level.
4. If the oil level is near or below the lower limit mark [2] on the
dipstick, fill with the recommended oil to the upper limit mark [3].
Do not overfill.
5. Reinstall the oil filler cap/dipstick [1].
Oil Change
See Figure 9, page 3.
Drain the engine oil when the engine is warm. Warm oil drains quickly
and completely.
1. Place a suitable container next to the engine to catch the used oil.
2. Remove the oil filler cap/dipstick [1], and the oil drain plug [2] and
washer [3].
3. Allow the used oil to drain completely; then reinstall the drain plug
and new washer. Tighten the drain plug securely.
Please dispose of used motor oil in a manner that is compatible
with the environment. We suggest you take used oil in a sealed
container to your local recycling center or service station for
reclamation. Do not throw it in the trash, pour it on the ground, or
pour it down a drain.
4. With the engine in a level position, fill to the upper limit mark
(bottom edge of the oil fill hole) on the dipstick with the
recommended oil. Do not overfill.
Capacity: 20 oz (0.58 L)
NOTICE
Running the engine with a low oil level can cause engine damage.
This type of damage is not covered by the DISTRIBUTOR'S
LIMITED WARRANTY.
5. Reinstall the oil filler cap/dipstick [1] securely.

AIR CLEANER

A properly maintained air filter will help prevent dirt from entering your
engine. Dirt entering the carburetor can be drawn into small passages
in the carburetor and cause premature engine wear. These small
passages can become blocked, causing starting or running problems.
You will need to clean the filter more frequently if you operate the
engine in very dusty areas.
NOTICE
Operating the engine without an air filter, or with a damaged filter, will
allow dirt to enter the engine, causing rapid engine wear. This type of
damage is not covered under your DISTRIBUTOR'S LIMITED
WARRANTY.
We recommend the use of a Honda Genuine air filter to ensure it
seals and performs as designed. Using a non-Honda air filter can
result in dirt bypassing the filter, causing damage to the engine or fuel
system.
Inspection
See Figure 10 page 3.
,
1. Press the latch tabs [1] on the top of the air cleaner cover [2], and
remove the cover. Check the filter [3] to be sure it is clean and in
good condition.
2. Reinstall the filter and air cleaner cover.
Cleaning
1. Tap the filter several times on a hard surface to remove dirt, or
blow compressed air not exceeding 30 psi (207 kPa) through the
filter from the clean side that faces the engine. Never try to brush
off dirt. Brushing will force dirt into the fibers.
2. Wipe dirt from the air cleaner body [4] and cover using a moist rag.
Be careful to prevent dirt from entering the air duct [5] that leads to
the carburetor.
ENGLISH
7