Functional Description; Extension Cords - Milwaukee 6391 Manual Del Operador

•
Some dust created by power sanding,
WARNING
sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
• lead from lead-based paint
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to
filter out microscopic particles.

FUNCTIONAL DESCRIPTION

4
3
1. Handle release lever
2. Handle lever release button
3. Bevel scale
4. Bevel pointer
5. Depth adjusting lever
6. Trigger
7. Depth setting gauge (not shown)
8. Spindle lock button
9. Bevel adjusting lever
10. Tilt-Lok™ handle
11. Upper guard
12. Lower guard lever
13. Blade
14. Shoe
15. Lower guard
16. Blade bolt
17. Outer blade flange
18. Inner flange
(not shown)
19. Sight line
20. Rip fence slot
21. Front handle
21
20
19
18
7
6
5
2
10
1
11
15
16
17
US
C
Cat. No. ...........................................................6391
Volts .......................................................120 AC/DC
8
Amps ...................................................................15
No Load RPM ..................................................6300
9
Blade Size. .................................................... 7-1/4"
Arbor ................................................................. 5/8"
Depth of Cut at 90° ............................. 0 to 2-15/32"
Depth of Cut at 45° ............................. 0 to 1-13/16"

EXTENSION CORDS

Grounded tools require a three wire extension
cord. Double insulated tools can use either a two
or three wire extension cord. As the distance from
the supply outlet increases, you must use a heavier
gauge extension cord. Using extension cords with
inadequately sized wire causes a serious drop in
voltage, resulting in loss of power and possible tool
damage. Refer to the table shown to determine the
required minimum wire size.
The smaller the gauge number of the wire, the greater
the capacity of the cord. For example, a 14 gauge
cord can carry a higher current than a 16 gauge cord.
When using more than one extension cord to make
up the total length, be sure each cord contains at
least the minimum wire size required. If you are using
one extension cord for more than one tool, add the
nameplate amperes and use the sum to determine
the required minimum wire size.
Guidelines for Using Extension Cords
• If you are using an extension cord outdoors, be sure
it is marked with the suffix "W-A" ("W" in Canada)
to indicate that it is acceptable for outdoor use.
• Be sure your extension cord is properly wired
and in good electrical condition. Always replace a
damaged extension cord or have it repaired by a
qualified person before using it.
12
• Protect your extension cords from sharp objects,
excessive heat and damp or wet areas.
Recommended Minimum Wire Gauge
Nameplate Amps
0 - 2.0
13
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 16.0
16.1 - 20.0
14
* Based on limiting the line voltage drop to five volts at 150%
of the rated amperes.
READ AND SAVE ALL INSTRUCTIONS
4
SYMBOLOGY
Double Insulated
Volts
Alternating Current/Direct Current
Amps
No Load Revolutions per Minute (RPM)
UL Listing for Canada and U.S.
SPECIFICATIONS
For Extension Cords*
Extension Cord Length
25' 50' 75'
18 18 18
18 18 18
18 18 16
18 16 14
16 14 12
14 12 10
12 10 --
FOR FUTURE USE.
100' 150'
18 16
16 14
14 12
12 12
10 --
-- --
-- --