Maintenance And Service; Accessories; Storage; Recycling - Narex EKV 21 Instrucciones De Uso

Long‑term Storage
After the device has been stored for an extended period of time, it
may not operate at full capacity right from the start when in impact
drilling mode. It is a common problem caused by hardened lubri-
cant in the impact drilling mechanism. Leave the device in impact
drilling mode and keep it running until the impact drilling mecha-
nism warms up sufficiently.
If you still have any issues after this, please contact an authorised
repair centre.

Maintenance and Service

Attention! Risk of injury by electric current. Unplug the
device from the power socket before making any ad‑
justments (such as mounting or removing hand grips,
making adjustments, replacing drill bits, etc.)!
‰ Always keep the air holes (14) clean.
‰ Regularly clean the plastic parts accessible from the outside
with a cloth without the use of detergents.
‰ After having used the device in demanding conditions for a
longer period of time, you should take the device for a service
inspection and thorough cleaning to a Narex authorised ser-
vice centre.
‰ The device is fitted with self-disconnecting carbon brushes. If
the brushes are worn down, the motor turns off automatically.
This prevents damaging the rotor. The carbon brushes can only
be replaced by an authorised service centre.
The device must undergo maintenance at regular intervals af‑
ter every ca 100 hours of use to guarantee good and constant
operation and long service life.
Regular maintenance involves the following steps:
‰ Cleaning the motor box, removing any sediments, dirt and
dust from the box.
‰ Cleaning the fastening hub.
‰ Checking the wear on the piston rings.
‰ Checking the wear on the carbon brushes.
‰ Replacing the grease fillings.
‰ Making sure the safety clutch is working correctly.
Attention! With the principles of protection against in‑
jury by electric current and the protection rating of the
device in mind, all maintenance and service work that
requires the removal of the machine's casing must be done
only by an authorised service centre!
You can find the current list of authorised service centres on our
website at www.narex.cz in the "Service Points" section.

Accessories

Accessories recommended for use with this device are commonly
available consumer accessories and can be purchased in shops sell-
ing electrical hand tools.

Storage

If stored packaged, the device can be stored in a dry storehouse
without heating if the temperature inside does not drop below
-5 °C.
If stored unpackaged, the device can only be stored in a dry store-
house where the temperature does not drop below +5 °C and
where there aren't any sudden changes in the temperature.

Recycling

Electrical tools, accessories and packaging should all be submitted
for reuse to prevent environmental damage.
EU countries only:
Do not put electrical tools into household waste!
In accordance with European Directive 2002/96/EC on waste elec-
trical and electronic equipment and the directive's enforcement in
national laws, unusable electrical tools must be collected for reuse/
recycling/recovery to prevent environmental damage.

Warranty

Our devices come with a warranty for material or production de-
fects in accordance with the legal regulations of the given country,
for a period no shorter than 12 months. In EU countries, the war-
ranty period is 24 months for exclusively private use (proven by an
invoice or bill of delivery).
Damage caused by natural wear and tear, overloading, improper
handling, damage caused by the user or by use contrary to the op-
erating manual, or damage known already at the time of purchase
is excluded from the warranty.
Complaints can be accepted only if the device is sent back to the
supplier or a NAREX authorised service centre in a non-disassem-
bled state. Store and keep the operating manual, safety instruc-
tions, list of spare parts and proof of purchase. Otherwise, the
manufacturer's current warranty terms always apply.
Note
Based on constant research and development, the manufacturer
reserves the right to change the technical information stated here.

Declaration of Conformity

The manufacturer declares that the machine meets all relevant
provisions of applicable European Community regulations.
Safety:
EN 60745-1; EN 60745-2-6
Directive 2006/42/EC
Electromagnetic compatibility:
EN 55014-1; EN 55014-2; EN 61000-3-2; EN 61000-3-3
Directive 2014/30/EU
RoHS:
Directive 2011/65/EU
The technical documentation is stored at:
Narex s.r.o., Chelčického 1932, 470 01 Česká Lípa, Czech Republic
2018
Narex s.r.o.
Chelčického 1932
470 01 Česká Lípa
English
Maciej Stajkowski
Executive Director
01. 08. 2018
15