Hammer Safety Warnings; Noise And Vibration Information; Use; Double Insulation - Narex EKV 21 Instrucciones De Uso

c) Do not expose power tools to rain or wet conditions. Water
entering a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension
cord suitable for outdoor use. Use of a cord suitable for out‑
door use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoida‑
ble, use a residual current device (RCD) protected supply.
Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power
tool while you are tired or under the influence of drugs,
alcohol or medication. A moment of inattention while oper‑
ating power tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye pro‑
tection. Protective equipment such as dust mask, non‑skid
safety shoes, hard hat, or hearing protection used for appro‑
priate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the
off‑position before connecting to power source and/or bat‑
tery pack, picking up or carrying the tool. Carrying power
tools with your finger on the switch or energising power tools
that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the
power tool on. A wrench or a key left attached to a rotating
part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all
times. This enables better control of the power tool in unex‑
pected situations.
f) Dress properly. Do not wear loose clothing or jewellery.
Keep your hair, clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair can be caught in
moving parts.
g) If devices are provided for the connection of dust extrac‑
tion and collection facilities, ensure these are connected
and properly used. Use of dust collection can reduce dust‑re‑
lated hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for
your application. The correct power tool will do the job better
and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on
and off. Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the
battery pack from the power tool before making any ad‑
justments, changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of starting
the power tool accidentally.
d) Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power tools
are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding
of moving parts, breakage of parts and any other condi‑
tion that may affect the power tool's operation. If dam‑
aged, have the power tool repaired before use. Many acci‑
dents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to bind
and are easier to control..
g) Use the power tool, accessories and tool bits etc. in ac‑
cordance with these instructions, taking into account the
working conditions and the work to be performed. Use of
the power tool for operations different from those intended
could result in a hazardous situation.
5) Service
a) Have your power tool serviced by a qualified repair person
using only identical replacement parts. This will ensure that
the safety of the power tool is maintained.

Hammer Safety Warnings

a) Wear ear protectors. Exposure to noise can cause hearing
loss.
b) Use auxiliary handle(s), if supplied with the tool. Loss of
control can cause personal injury.
c) Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory may
contact hidden wiring or its own cord. Cutting accessory
contacting a „live" wire may make exposed metal parts of
the power tool „live" and could give the operator an electric
shock.

Noise and Vibration Information

Noise Level
Values were measured in accordance with EN 60745.
Acoustic pressure level L = 90.5 dB (A).
pA
Acoustic output level L = 101.5 dB (A).
wA
Measurement inaccuracy K = 3 dB (A).
ATTENTION! Working with the device makes noise!
Use ear protection!
Vibrations
Weighted value of vibrations affecting the hands and arms:
Hammer drilling into concrete a
Measurement inaccuracy K = 1.5 m/s
The vibrations and noise level values mentioned here were
measured in accordance with the testing conditions stipulated
by EN 60745 used for comparing tools. They are also suitable as
a preliminary assessment of vibration and noise load before using
the device.
The noise levels and vibration values mentioned apply to the main
use of the electrical device. Using the electrical device for other
purposes than intended, or insufficient maintenance may lead to
a significant increase in noise level or vibration load during work.
To accurately assess the values during a predetermined work time,
it is also necessary to take into account how long the device has
been idle or how long the device has been turned off for during
this time. This may significantly reduce the load during the entire
work period.

Use

The light electro-pneumatic drilling hammer EKV 21 is designed
for impact drilling with solid (spiral) drill bits into concrete, stone
and brickwork. Combined with an adapter and chuck, this device
can be used for drilling or screwing into wood, metal and plastics.
This electro-pneumatic drilling hammer can only be used for the
aforementioned purposes and used in contexts specified by the
manufacturer.
This electro-pneumatic drilling hammer is not suitable for impact
drilling with hollow bits or for drilling with hole saws and hole
punches.

Double Insulation

For maximum user safety, our devices are built to meet valid Eu-
ropean regulations (EN standards). Devices with double insulation
are marked with an international symbol - a double square. Such
devices must not be grounded and can be powered by a cable
with only two cores. The devices have interference elimination in
accordance with EN 55014.
English
= 13.22 m/s .
2
h
.
2
13