EINHELL TE-MS 2112 L Manual De Instrucciones página 28

6.3 Miter cut 0°- 45° and turntable 0°
(Fig. 1-3, 12)
The crosscut saw can be used to make miter cuts
of 0- 45° in relation to the work face.
•
If necessary, dismantle the clamping device
(8) from the left side of the saw table (18) or
mount on the right-hand side of the fixed saw
table (18).
•
Move the machine head (4) to its upper po-
sition.
•
Fasten the turntable (17) in 0° position.
•
Cut as described in section 6.1.
6.4 Miter cut 0°- 45° and turntable 0°- 45°
(Fig. 1-3, 13)
The crosscut saw can be used to make miter cuts
to the left of 0°-45° in relation to the work surface,
with simultaneous setting of the turntable from
0°-45° to the left or 0°-45° to the right in relation to
the stop rail (double miter cut).
•
If required, dismantle the clamping device
(8) or mount on the opposite side of the fixed
saw table (18).
•
Move the machine head (4) to its upper po-
sition.
•
Release the turntable (17) by undoing the
locking screw (14).
•
Use the handle (1) to adjust the turntable (17)
to the angle required (in this connection see
also section 6.2).
•
Retighten the locking screw (14) to secure the
turntable in place.
•
Adjust the miter angle on the machine head
and the stop rail as described in section 5.5.
•
Cut as described in section 6.1.
6.5 Limiting the cutting depth (Fig. 3)
•
The cutting depth can be infinitely adjusted
using the screw (27). To do so, undo the
knurled nut on the screw (27). Turn the screw
(27) in or out to set the required cutting depth
and then retighten the knurled nut on the
screw (27).
•
Check the setting by completing a test cut.
6.6 Sawdust bag (Fig. 2)
The saw is equipped with a sawdust bag (22).
The sawdust bag (22) can be emptied by means
of a zipper at the bottom.
GB
6.7 Changing the saw blade (Fig. 1, 14-15)
•
•
•
•
•
•
•
•
•
•
•
•
6.8 Transport (Fig. 1-3)
•
•
•
•
6.9 Operating the laser (Fig. 2)
To switch on: Move the On/Off switch (36) to the
"I" position to switch on the laser (35). A laser line
is projected onto the material you wish to pro-
cess, providing an exact guide for the cut.
To switch off : Move the On/Off switch (36) to the
"0" position.
www.sidirika-nikolaidi.gr
- 28 -
Before changing the saw blade: Pull out the
power plug!
Wear work gloves to prevent injury when
changing the saw blade.
Press the saw shaft lock (5) with one hand
while positioning the Allen key (d) on the
flange bolt (31) with the other hand. The saw
shaft lock (5) engages after no more than one
rotation.
Now, using a little more force, slacken the
flange screw (31) in the clockwise direction.
Turn the flange screw (31) right out and remo-
ve the external flange (32).
Take the blade (7) off the inner flange and pull
out downwards.
Carefully clean the flange screw (31), outer
flange (32) and inner flange.
Fit and fasten the new saw blade (7) in rever-
se order.
Important! The cutting angle of the teeth, in
other words the direction of rotation of the
saw blade (7) must coincide with the direction
of the arrow on the housing.
Check to make sure that all safety devices
are properly mounted and in good working
condition before you begin working with the
saw again.
Important! Every time that you change the
saw blade, check to see that it spins freely in
the table insert (12)in both perpendicular and
45° angle settings.
Important! The work to change and align the
saw blade (7) must be carried out correctly.
Retighten the locking screw (14) to secure the
turntable (17) in place.
Activate the release button (3), press the ma-
chine head (4) downwards and secure with
the safety pin (25). The saw is now locked in
its bottom position.
Carry the machine by the fixed transport
handle.
To set up the equipment again, proceed as
described in section 5.2.