Operation - EINHELL TE-MS 2112 L Manual De Instrucciones

and lock into place with the locking screw
(14). The saw has locking positions at the
following angles: -45°, -40°, -35°, -30°, -22.5°,
-15°, -10°, -5°, 0°, 5°, 10°, 15°, 22.5°, 30°,
35°, 40° and 45°.
•
To release the saw from its position at the
bottom, pull the fastening bolt (25) out of the
motor mounting while pressing down lightly
on the machine head (4). Turn the fastening
bolt (25) through 90° before releasing it, so
that the saw remains unlocked.
•
Swing up the machine head (4).
•
The clamping device (8) can be fitted on the
left or right of the fixed saw table (18).
•
For the horizontal clamping of workpieces you
can anchor the clamping device in the holder
(33).
•
- To move out the workpiece supports (10)
press the lever on the bottom side of the
workpiece support and then pull the workpie-
ce support outwards to the right or left.
•
For repeat cuts of identical length you can
unfold the longitudinal stop (13).
•
When the locking grip (21) is undone, you
can tilt the machine head (4) to the left by up
to 45°.
5.3 Precision adjustment of the stop for cros-
scut 90° (Fig. 1,6-7)
•
Fasten the turntable (17) in 0° position.
•
Undo the locking grip (21) and tilt the machi-
ne head (4) all the way to the right using the
handle (1).
•
Place the 90° angular stop (a) between the
blade (7) and the turntable (17).
•
Adjust the adjustment screw (29) until the
angle between the blade (7) and the turntable
(17) equals 90°.
•
Finally, check the position of the pointer (20)
on the scale (19)
•
No stop angle included.
5.4 Precision adjustment of the stop for 45°
miter cuts (Fig. 1, 8-9)
•
Fasten the turntable (17) in 0° position.
•
Undo the locking grip (21) and tilt the machi-
ne head (4) all the way to the left to 45° using
the handle (1).
•
Place the 45° stop angle (b) between the bla-
de (7) and the turntable (17).
•
Adjust the adjustment screw (30) so that the
angle between the blade (7) and the turntable
(17) equals exactly 45°.
•
No stop angle included.
GB
5.5 Adjusting the miter angle on the machine
•
•
•
•
•

6. Operation

6.1 Cross cut 90° and turntable 0°
•
•
•
•
•
•
•
Important! The integral resetting springs will
automatically lift the machine head. Do not simply
let go of the handle (1) after cutting, but allow the
machine head (4) to rise slowly, applying slight
counter pressure as it does so.
6.2 Cross cut 90° and turntable 0° - 45°
The crosscut saw can be used to make crosscuts
of 0°- 45° to the left and 0° - 45° to the right in re-
lation to the stop rail.
•
•
•
•
www.sidirika-nikolaidi.gr
- 27 -
head (Fig. 2, 12-13)
Undo the locking grip (21).
Hold the machine head (4) by the handle (1).
After the locking grip is undone, the machine
head can be infinitely tilted as well as tilted to
various locking positions.
Angles to the left: 0-45°
Re-tighten the locking grip (21).
(Fig. 1-3, 10)
Move the machine head (4) to its upper po-
sition.
Place the piece of wood to be cut at the stop
rail (11) and on the turntable (17).
Lock the material with the clamping device
(8) on the fixed saw table (18) to prevent the
material from moving during the cutting ope-
ration.
Press the release button (3) to release the
machine head (4).
Press the On/Off switch (2) to start the motor.
Use the handle (1) to move the machine head
(4) steadily and with light pressure down-
wards until the saw blade (7) has completely
cut through the workpiece.
When the cutting operation is completed,
move the machine head (4) back to its upper
(home) position and release the On/Off but-
ton (2).
(Fig. 1-3, 11)
Release the turntable (17) by slackening the
locking screw (14).
Turn the turntable (17) and scale pointer (15)
to the desired angular setting on the dial (16)
and lock into place with the locking screw
(14).
Retighten the locking screw (14) to secure the
turntable (17) in place.
Cut as described in section 6.1.