Accessories; Cross Cutting Guide Rail - Festool HK 55 EQ Manual De Instrucciones

Observe the following instructions:
► To ensure constant air circulation, always
keep the cooling air openings in the housing
clean and free of blockages.
► Use an extractor on all openings of the pow­
er tool to remove wood chips and splinters.
► The pendulum guard must always be able to
move freely and close independently. Al­
ways keep the area around the pendulum
guard clean. Clear from dust and chippings
by blowing out with compressed air or using
a brush.

11 Accessories

Use only original Festool accessories and
Festool consumable material intended for this
machine. These components are designed spe­
cifically for this machine. Using accessories
and consumable material from other suppliers
will most likely affect the quality of your results
and limit warranty claims. Machine wear or
your own personal workload may increase de­
pending on the application. Protect yourself and
your machine, and preserve your warranty
claims by always using original Festool acces­
sories and Festool consumable material!
The order numbers of the accessories and tools
can be found in the Festool catalogue or on the
Internet under "www.festoolusa.com".
In addition to the accessories described,
Festool also provides a comprehensive range of
system accessories that allow you to use your
saw more effectively and in diverse applica­
tions, e.g.:
• Parallel stop, extension table PA-HKC 55
• Kickback stop FS-RSP
• Parallel stop FS-PA and guide extension
FS-PA-VL
• Side-mounted cover, false joint ABSA-TS
55
11.1 Saw blades, other accessories
In order to saw different materials quickly and
cleanly, Festool offers saw blades for all appli­
cations that are specially designed for your
Festool portable circular saw.
11.2 Guide rail
The guide rail enables you to make clean, accu­
rate cuts while simultaneously protecting the
surface of the workpiece from damage.
In conjunction with the extensive range of ac­
cessories, exact angled cuts, mitre cuts and fit­
ting work can be completed with the guide sys­
tem. The option of attaching the guide rail se­
curely using clamps [8-7] ensures safer work­
ing conditions.
► Adjust the guide play between the saw table
and the guide rail using the two adjustable
jaws [8-8].
The splinterguard [8-5] requires breaking in
before first usage:
► Position saw at the very end of the guide
rail, so that the guide plate is level.
► Swivel saw to 0° position and set to maxi­
mum cutting depth.
► Switch on saw.
► Slowly push saw along the entire length of
the rail.
The edge of the splinterguard now corresponds
exactly to the cutting edge.

11.3 Cross cutting guide rail

The cross cutting guide rail is designed for saw­
ing wood and panel materials.
It enables precise and clean cuts, in particular
angled cuts can be performed simply and with
repeat accuracy. The saw automatically moves
back to the initial position after the sawing
process.
Observe the instructions in the operating man­
ual for the FSK cross cutting guide rail
11.4 SYSTAINER
Systainer
Many Festool products are shipped in a unique
system container, called "Systainer". This pro­
vides protection and storage for the tool and ac­
cessories. The Systainers are stackable and
can be interlocked together. They also can be
interlocked atop Festool CT dust extractors.
To open the Systainer
Turn the T-loc [SYS-b-1] to this posi­
tion.
To lock the Systainer
Turn the T-loc [SYS-b-1] to this posi­
tion.
To connect two Systainers
Place one Systainer on the top of the other
(Fig. [SYS-a]).
Turn the T-loc [SYS-b-1] to one of
this positions (Fig. [Sys-b]).
The Systainers are connected and locked.
English
17