Effect Parameters; Beat Effect - Pioneer DJM-800 Manual De Instrucciones

EFFECT FUNCTIONS (EFFECT PARAMETERS)

EFFECT PARAMETERS

Beat Effect

Name
1 DELAY Sets delay time of 1/8 to 16/1 per 1
beat of BPM time.
2 ECHO (*1) Sets delay time of 1/8 to 16/1 per 1
beat of BPM time.
3 REVERSE DELAY Sets delay time of 1/8 to 16/1 per 1
beat of BPM time.
4 PAN Sets time of 1/16 to 16/1 per 1 beat of
BPM time for distribution to right/left.
5 TRANS Sets cut time of 1/16 to 16/1 per 1
beat of BPM time.
6 FILTER Cycle of cutoff frequency shift is set
in unit of 1/4 to 64/1 relative to 1
beat of BPM.
7 FLANGER Cycle of flanger shift is set in units
of 1/4 to 64/1 relative to 1 beat of
BPM.
8 PHASER Cycle of phaser effect shift is set in
units of 1/4 to 64/1 relative to 1 beat
of BPM.
9 REVERB (*1) Amount of reverberation is set from
1 to 100 %.
10 ROBOT Sets pitch of robot sound effect
within range of –100 to +100 %.
11 CHORUS Cycle of chorus sound waver is set
in units of 1/4 to 64/1 relative to 1
beat of BPM.
12 ROLL (*2) Effect time is set as 1/16 to 16/1
relative of 1 beat of BPM.
13 REVERSE ROLL (*2) Effect time is set as 1/16 to 16/1
relative of 1 beat of BPM.
14 SEND/RETURN
(*1) Even if the effect monitor is turned ON, if no sound is output from the channel to the master output, the effect sound will not be heard.
(*2) When effect is disabled (OFF), the effect sound will not be heard, even if monitor is set to effector.
Sound-color effects
Name
1 HARMONIC Sets amount of pitch shift in range of ±6 half-tones. Rotating dial
to right increases pitch shift by +6 half-tones, while rotating to the
left reduces pitch shift by –6 half-tones.
2 SWEEP Sets filter's cutoff frequency. Rotating dial clockwise produces
band-pass filter effect; rotating counterclockwise produces notch
filter effect.
3 CRUSH Sets amount of crushing of input sound. Rotate dial
counterclockwise to emphasize low-range sounds, and rotate
clockwise to emphasize high-range sounds.
4 FILTER Sets cutoff frequency of filter. Rotating dial to right changes high-
pass filter; rotating dial to left changes low-pass filter.
18
<DRB1394>
En
Beat Switch Parameter
—
Parameter (COLOR dial)
Parameter 1 (TIME dial)
Contents Setting Range (unit)
Sets delay time. 1 to 4 000 (ms)
Sets delay time. 1 to 4 000 (ms)
Sets delay time. 10 to 4 000 (ms)
Sets effect time. 10 to 16 000 (ms)
Sets effect time. 10 to 16 000 (ms)
Sets cycle for 10 to 32 000 (ms)
cutoff time shift.
Sets cycle for 10 to 32 000 (ms)
flanger effect
shift.
Sets cycle for 10 to 32 000 (ms)
phase effect shift.
Sets amount of 1 to 100 (%)
reverberation
effect.
Sets pitch of –100 to +100 (%)
robot sound
effect.
Sets cycle of 10 to 32 000 (ms)
chorus sound
harmonic.
Sets effect time. 1 to 4 000 (ms)
Sets effect time. 1 to 4 000 (ms)
—
Parameter 2
(MIX/DEPTH dial) contents
Sets balance between original and
delay sound.
Sets balance between original
sound and echo sound.
Sets balance between original and
delay sound.
Sets balance between original
sound and effect sound.
Sets balance between original
sound and effect sound.
Amount of effect increases when
dial is turned clockwise.
Amount of effect increases when
dial is turned clockwise. When dial
is turned fully counterclockwise,
only original sound is output.
Amount of effect increases when
dial is turned clockwise. When dial
is turned fully counterclockwise,
only original sound is output.
Sets balance between original
sound and effect sound.
Amount of effect increases when
dial is turned clockwise.
Sets balance of chorus sound.
Sets balance of original sound and
roll sound.
Sets balance of original sound and
roll sound.
— Sets volume of RETURN input
sound.