Decommissioning; Information For Service Technicians; Software - Rancilio KRYO 65 OD Manual De Instrucciones

8. DECOMMISSIONING

8.1. Temporary
- Close the hopper and grind the coffee beans remaining between
the burrs.
- Turn off the switch and unplug the appliance from the power
source;
- Remove any coffee beans remaining in the bean hopper.
- Perform cleaning and maintenance operations;
- Coil up the supply cable and attach it to the machine using
adhesive tape;
- Cover the machine and place it in a dry place, sheltered from
bad weather and to which you have exclusive access.
8.2. Final
In addition to the operations of temporary decommissioning:
- Cut the power cable,
- Pack up the machine using cardboard or similar materials
and hand it over to specialized operators (authorized waste
disposal collectors or dealers in second-hand goods)

9. INFORMATION FOR SERVICE TECHNICIANS

9.1. Replacement of burrs
Although manufactured in tempered steel, the burrs are subject
to wear and tear.
Their lifespan is influenced by the amount of coffee ground, its
hardness and degree of roasting, as well as the quantity and
purity of the coffee beans.
Small stones and various impurities have a marked abrasive
action which significantly reduces the lifespan of the burrs.
When grinding time becomes noticeably longer or the grind
becomes irregular, the burrs should be replaced as follows:
- Pull the hopper locking slide (Fig. 1–4);
- Start the grinder to grind the coffee remaining between the
burrs;
- Once grinding has finished, turn off the machine and unplug
from the power source;
- Empty the bean hopper (Fig. 1–2);
- Remove the regulation knob (Fig. 1–3);
- Turn the upper burr-holder (Fig. 4–1) counter-clockwise until
the head emerges completely;
- Unscrew the screws (Fig. 4–2) and remove the burrs (Fig. 4–3)
from the burr-holder:
- Carefully clean the burr supports, the burr-holder thread and
its housing;
- Position the new burrs in their holders and block them firmly
in place;
- Reassemble the machine, performing the previous steps in
reverse.
- Calibrate the new burrs.
9.2. Calibration of grinder burrs
To be performed after burr replacement
The grinders are tested with a medium grind setting, and need to
be readjusted. This operation should be carried out with the bean
hopper empty.
Remove the protection lid (Fig. 1b-5), hold down the adjustment
unlock button (Fig. 2-1) and at the same time slowly turn the
adjustment knob (Fig. 2-3) counter-clockwise until the burrs
brush against each other. Release the button, turn the numbered
ring (Fig. 2-2) so that the starting point 0 is frontal; move the
adjustment knob (Fig. 2-3) in the opposite direction (clockwise).
12
9.3. Technician menu
Must be performed by a qualified technician.
The access to the technician menu is given by switching off the
grinder. Switch on the main switch (Fig. 1-9) while pressing the
confirmation button.

10. SOFTWARE

KRYO 65 OD has three menus to operate with.
10.1 Use of Buttons
To configure the KRYO 65 OD the dose buttons will be used with
an additional function.
The single dose button (Fig. 1b-12) will be used as "-"button, the
double dose button (Fig. 1b-13) as "+"button and both buttons to
browse through the menu. The customized dose button (Fig. 1b-
14) is used as confirmation or ESC-button depending on the
menu accessed.
10.2 Dosing menu
In the dosing menu the amount of coffee dispensed by one button
can be changed.
- Press the selected button for 3 seconds
- Change the value of the specific button
- Confirm the change with the confirmation button
10.3 Barista menu
Open the "Barista Menu" by pressing the confirmation button
(Fig. 1-14) for 5 seconds.
Any additional information is given in the software tree below.
10.4 Technician menu
Must be performed by a qualified technician.
The parameters with the grey background are only accessible for
the service technician
The access to this menu is given in another chapter of the manual.