Milwaukee 4931 Manual Del Operario página 9

Esmeriladora de banco para servicio pesado
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

MAINTENANCE
To reduce the risk of injury, always unplug
your tool before performing any mainte-
nance. Never disassemble the tool or try to
do any rewiring on the tool's electrical sys-
tem. Contact a MILWAUKEE service facility
for ALL repairs.
Maintaining Tools
Keep your tool in good repair by adopting a regular maintenance pro-
gram. Before use, examine the general condition of your tool. Inspect
guards, switches, tool cord set and extension cord for damage. Check
for loose screws, misalignment, binding of moving parts, improper mount-
ing, broken parts and any other condition that may affect its safe opera-
tion. If abnormal noise or vibration occurs, turn the tool off immediately
and have the problem corrected before further use. Do not use a dam-
aged tool.
Tag damaged tools "DO NOT USE" until repaired
(see "Repairs").
To reduce the risk of injury, electric shock
and damage to the tool, never immerse your
tool in liquid or allow liquid to flow inside the
tool.
Repairs
If your tool is damaged, return the entire tool to the nearest service
center listed on the back cover of this operator's manual.
To reduce the risk of injury, use only
identical replacement parts.
FIVE YEAR TOOL LIMITED WARRANTY
Every MILWAUKEE tool is tested before leaving the factory and is war-
ranted to be free from defects in material and workmanship. MILWAUKEE
will repair or replace (at MILWAUKEE 's discretion), without charge, any
tool (including battery chargers) which examination proves to be defec-
tive in material or workmanship from five (5) years after the date of
purchase. Return the tool and a copy of the purchase receipt or other
proof of purchase to a MILWAUKEE Factory Service/Sales Support
Branch location or MILWAUKEE Authorized Service Station, freight pre-
paid and insured. This warranty does not cover damage from repairs
made or attempted by other than MILWAUKEE authorized personnel,
abuse, normal wear and tear, lack of maintenance, or accidents.
Battery Packs, Flashlights, and Radios are warranted for one (1) year
from the date of purchase.
THE REPAIR AND REPLACEMENT REMEDIES DESCRIBED HEREIN ARE
EXCLUSIVE. IN NO EVENT SHALL MILWAUKEE BE LIABLE FOR ANY
INCIDENTAL, SPECIAL, OR CONSEQUENTIAL DAMAGES, INCLUDING
LOSS OF PROFITS.
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRAN-
TIES, OR CONDITIONS, WRITTEN OR ORAL, EXPRESSED OR IMPLIED FOR
MERCHANTABLILITY OR FITNESS FOR PARTICULAR USE OR PURPOSE.
This warranty gives you specific legal rights. You may also have other
rights that vary from state to state and province to province. In those
states that do not allow the exclusion of implied warranties or limitation
of incidental or consequential damages, the above limitations or exclu-
sions may not apply to you. This warranty applies to the United States,
Canada, and Mexico only.
WARNING!
WARNING!
WARNING!
ACCESSORIES
Unplug tool before removing or attaching
accessories. Maximum Safe Operating
Speed of wire brush and grinding wheel
must be greater than no load RPM of tool.
Guards must be used with grinding wheels
and wire wheels. Only use specifically
recommended accessories. Others may
be hazardous.
For a complete listing of accessories refer to your MILWAUKEE Electric
Tool catalog or go on-line to www.mil-electric-tool.com. To obtain a cata-
log, contact your local distributor or a service center listed on the back
cover of this operator's manual.
Wheels For Bench Grinders
NOTE: The maximum safe operating speed shown on the grinding and
wire wheels must be greater than the load speed of the tool.
Grinding Wheels
Grinding Wheels are available in 36, 60, and 80 vitrified grit for all types
of grinding.
Knot Wire Wheels
Use Knot Wire Wheels for removing rust, scales and file marks.
Brushes
Brushes are made of select steel wire and have a face width of 3/4".
Cloth Buffing Wheels
Use Cloth Buffing Wheels for buff-
ing metal surfaces. These wheels
are made of multiple layers of select
buffing cloth sewed securely to-
gether and can be coated with glue
and dipped in emery grit for finish
grinding or rough polishing.
Plexiglass Lens
Replacement lens for all light eye
shield models and Catalog No. 4995.
Supplied individually.
Plexiglass Eye Shield (Pair)
Furnished as standard equipment on
Catalog No. 4935. Easily replaced
when pitted. Supplied as a pair.
Grinder Pedestal
Heavy grey iron casting with tubular
steel column. Removable water pot.
Adaptable to all models.
WARNING!
Page 9

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

49354991499550515091

Tabla de contenido