Setting Bass Compressor; Setting Bass Focus; Speaker Setup - Alpine DVA-9860 Manual De Uso

Setting Bass Compressor

You can adjust the sound of low frequencies as desired.
1
Check that Defeat mode is off (page 17).
2
Press and hold CENTER f. for at least 2 seconds.
The audio processor control mode is activated.
3
Select the BASS SOUND mode by pressing
CENTER f. repeatedly.
4
Select BASS COMP. by pressing g or f.
5
Select the desired mode by turning and then
pressing the Rotary encoder.
Bass sound is emphasized more as the mode is
sequentially switched as COMP1 → 2 → 3, offering you
vivid low frequencies.
Select OFF when the setting is not necessary.
6
When the setting is complete, press and hold
CENTER f. for at least 2 seconds.
The unit returns to the normal mode.
Press CENTER f. to select another item to be set.

Setting Bass Focus

Using the previously specified delay number (time difference) allows
you to set a time difference between the front-rear/left-right speakers.
Namely, it enables a time correction based on your preference. With
an initial delay of 0.05 ms for each of the 0 to 400 steps, audible time
correction can be achieved.
1
Check that Defeat mode is off (page 17).
2
Press and hold CENTER f. for at least 2 seconds.
The audio processor control mode is activated.
3
Select the BASS SOUND mode by pressing
CENTER f. repeatedly.
4
Select BASS FOCUS by pressing g or f.
5
Press the Rotary encoder to select the front/rear/
left/right speaker.
6
Set a step of the front (left and right) speaker, and
press the Rotary encoder.
7
When the setting is complete, press and hold
CENTER f. for at least 2 seconds.
The unit returns to the normal mode.
Press CENTER f. to select another item to be set.
• Any setting in Bass Focus is applied in time correction, too.
• When the setting is complete, it is recommended to store the setting
contents. For storing, refer to page 37.
34
-EN

Speaker Setup

The PXA-H700 or PXA-H701 can be set according to the playable
frequency range of your speakers.
Check the playable frequency range of the speakers (not including the
subwoofer) before performing this operation to verify whether the
speakers can play low frequencies (of about 80 Hz or less).
• Avoid stopping, pausing, switching the disc, cueing, fast-
forwarding or switching the audio channel of this unit while
making this adjustment. The setting is cancelled if Decode mode is
switched.
1
Check that Defeat mode is off (page 17).
2
Press and hold CENTER f. for at least 2 seconds.
The audio processor control mode is activated.
3
Select the SP SETUP mode by pressing
CENTER f. repeatedly.
4
Select the speaker by pressing the Rotary
encoder.
5
Select the speaker characteristic by turning and
then pressing the Rotary encoder.
OFF* 1 : When no speaker is connected.
SMALL: When a speaker that cannot play low
frequencies (80 Hz or less) is connected.
LARGE* 2 : When a speaker that can play low frequencies
(80 Hz or less) is connected.
It is not possible to set the front speakers to "OFF".
*
1
* If the front speakers are set to "SMALL", the rear and
2
centre speakers cannot be set to "LARGE".
6
When the setting is complete, press and hold
CENTER f. for at least 2 seconds.
The unit returns to the normal mode.
Press CENTER f. to select another item to be set.
• If the centre speaker is turned "OFF," the centre channel's audio
signals are added to the audio signals output from the front
speakers.
• If you set the speaker response to "OFF," also set the speaker
setting to "OFF." (page 30)
• Perform the setup for all the speakers ("Front," "Center," "Rear"
and "Subwoofer"). If not, the sound may not be balanced.
• When centre is set to "OFF", the setting is ineffective even if
centre is set with this function.
• Through changing the settings on each speaker, a change in the
output of the other speakers may occur due to the setting
requirements.
• When using the PRO LOGIC II, if the rear speaker is set to
"LARGE", then there will be no output from the subwoofer.
• When the setting is complete, it is recommended to store the setting
contents. For storing, refer to page 37.