Bosch 1617 Instrucciones De Funcionamiento Y Seguridad página 4

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

clockwise.
Feed direction
of cutting
must
be counter-clockwise.
NOTE:
inside
and
outside
cuts
will
require
different
feed
direction,
refer
to section
on feeding
the
router.
Feeding
the
tool
in the
wrong
direction,
causes
the cutting
edge
of the bit
to climb
out of the work and pull the tool in
the direction
of this feed.
Never
use dull or damaged
bits.
Sharp
bits must be handled
with care. Damaged
bits can snap
during
use. Dull bits require
more force to push the tool, possibly
causing
the bit to break.
Never touch the bit during or immediately
after the use. After use the bit is too hot to
be touched
by bare hands.
Never
lay the tool
down
until the motor
has
come
to a complete
standstill.
The
spinning
bit can grab the surface and pull the
tool out of your control.
Never
use
bits
that
have
a cutting
diameter
greater
than
the opening
in the
base.
Some
dust
created
by
power
sanding,
sawing,
grinding,
drilling,
and other
construction
activities
contains
chemicals
known
to
cause
cancer,
birth
defects
or other
reproductive
harm,
Some
examples
of
these chemicals
are:
• Lead from lead-based
paints,
• Crystalline
silica
from bricks
and cement
and other masonry products,
and
• Arsenic
and chromium
from
chemically-
treated lumber.
Your
risk
from
these
exposures
varies,
depending
on how often you do this type of
work.
To reduce
your
exposure
to these
chemicals:
work in a well ventilated
area, and
work with approved
safety
equipment,
such
as those
dust
masks
that
are
specially
designed
to filter out microscopic
particles.
Safety
Rules for Router Table
Read and understand
the tool manual
and
these
instructions
for the use of this table
with
your
router,
Failure
to follow
all
instructions
listed below may result in serious
personal
injury.
Unplug
tool
before
setting
up in table,
making
adjustments
or changing
bits.
Accidental
start-up
of the tool
can
cause
injury.
Fully
assemble
and
tighten
all
the
fasteners
required
for
this
table
and
mounting
the
router.
Also
remember
to
occasionally
check the stand and make sure
it is still tight.
A loose stand is unstable
and
may shift in use and cause serious
injury.
Before
operating
make sure the entire
unit
is placed
on a solid,
flat,
level
surface.
Serious
injury could occur if tool is unstable
and tips.
Never stand
on the table
or use as ladder
or scaffolding.
Serious
injury could occur if
the table
is tipped
or the cutting
tool
is
accidentally
contacted.
Do
not
store
materials
on or near the table such that it is
necessary
to stand on the table or its stand
to reach them.
Never
use dull or damaged
bits.
Sharp
bits must be handled
with care.
Damaged
bits can snap
during
use.
Dull bits require
more force
to push the workpiece,
possibly
causing the bit to break.
Match the appropriate
bit and its speed
to
your
application.
Do not
use
bits
that
have
a cutting
diameter
that exceeds
the
capacity
of the tool.
Overloading
the tool
can lead to personal
injury or tool failure.
Never
start
the
tool
when
the
bit
is
engaged
in the material.
The
bit cutting
edge may grab the material
causing
loss of
control of the workpiece.
Router
bits
are intended
for wood,
wood
products
and
plastic
only.
Be sure the
workpiece
does
not
contain
nails,
etc.
before
routing.
Cutting a nail or the like will
cause
the carbides
to be dislodged,
fly
toward the operator
side, and possibly
strike
you or bystanders.
-4-

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

1617evs1617pk1617evspk16181618evs0 601 617 061

Tabla de contenido