Maytag MED5591TQ1 Manual De Uso página 18

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Check t helevelness
ofthe dryer, Check l evelness
first s ide toside, t hen front t oback.
Ifthedryer isnotlevel, prop upthe dryer using a wood block. Use awrench t oadjust the legs
upordown and check a gain f orlevelness.
You canchange your d oor s wing f rom aright-side opening toa left-side opening, ifdesired.
oB
G
1.
Place towel
(A) on top of dryer to protect
surface.
2.
Open
dryer door. Remove
bottom
screws from cabinet
side of hinges (C). loosen
(do not
remove/top
screws from cabinet
side of hinges.
3.
lift door until top screws in cabinet
are in large part of hinge slot. Pull door forward
off
screws.
Set door (handle
side up) on top of dryer. Remove top screws from cabinet.
4.
Remove screws attaching
hinges to door.
5.
Use a small, flat-blade
screwdriver
to gently remove
4 hinge hole plugs (D) on left side of
cabinet.
Insert plugs into hinge holes on right side of cabinet.
6_
7_
Insert screws into bottom
holes on left side of cabinet.
Tighten
screws halfway.
Position
door so large end of door hinge slot is over screws. Slide door up so screws are in bottom
of slots. Tighten
screws. Insert and tighten
top screws in hinges.
Close door and check that door strike aligns with door catch (B). If it is needed,
slide door
catch left or right within
slot to adjust alignment.
1.
Check that all parts are now installed.
If there is an extra part, go back through
the steps to
see which step was skipped.
2.
Check that you have all of your tools.
3.
Dispose
of/recycle
all packaging
materials.
4.
Check the dryer's final location.
Be sure the vent is not crushed
or kinked.
5.
Check that the dryer is level. See "kevel
Dryer."
6.
In the U.S.A.
For power supply
cord installation,
plug into an outlet.
For direct wire installation,
turn on power.
In Canada
Plug into a grounded
4 prong outlet.
lurn
on power.
7.
Remove any protective
film on the console
and any tape remaining
on the dryer.
8.
Read "Dryer
Use."
9.
Wipe
the dryer drum
interior
thoroughly
with a damp cloth to remove
any dust.
10. Set the dryer on a full heat cycle (not an air cycle) for 20 minutes
and start the dryer.
If the dryer will not start,
check the following:
Controls
are set in a running
or "On"
position.
Start button
has been pushed firmly.
Dryer is plugged
into an outlet
and/or electrical
supply
is on.
Household
fuse is intact and tight, or circuit
breaker
has not tripped.
Dryer door is closed.
11. When
the dryer has been running
for 5 minutes,
open
the dryer door and feel for heat. [f
you feel heat, cancel
cycle and close the door.
If you do not feel heat, turn off the dryer and check
the following:
There may be 2 household
fuses or circuit
breakers for the dryer. Check that both fuses
are intact and tight, or that both circuit
breakers have not tripped.
[f there is still no
heat, contact
a qualified
technician.
NOTE: You may notice a burning
odor when the dryer is first heated.
This odor is common
when the heating element
is first used. The odor will go away.
18

Publicidad

Tabla de contenido
loading

Tabla de contenido