Test Run; Before Test Run - Mitsubishi Electric Mr. Slim PLA-RP-AA Serie Manual De Instalación

7. Electrical work
Function table
Select unit number 00
Mode
Power failure automatic recovery
Indoor temperature detecting
LOSSNAY connectivity
Power voltage
Auto mode (only for PUHZ)
Select unit numbers 01 to 03 or all units (AL [wired remote controller]/07 [wireless remote controller])
Mode
Filter sign
Fan speed
No. of air outlets
Installed options (high-performance filter)
Up/down vane setting
Energy saving air flow
(Heating mode)

8. Test run

8.1. Before test run

s After completing installation and the wiring and piping of the indoor and outdoor
units, check for refrigerant leakage, looseness in the power supply or control
wiring, wrong polarity, and no disconnection of one phase in the supply.
s Use a 500-volt megohmmeter to check that the resistance between the power
supply terminals and ground is at least 1.0MΩ.
F E
CENTRALLY CONTROLLED
CHECK
STAND BY
DEFROST
TEMP.
G H
7
MODE
3,4
CHECK
TEST RUN
2
Settings
Not available
Available
Indoor unit operating average
Set by indoor unit's remote controller
Remote controller's internal sensor
Not Supported
Supported (indoor unit is not equipped with outdoor-air intake)
Supported (indoor unit is equipped with outdoor-air intake)
240 V
220 V, 230 V
Energy saving cycle automatically enabled
Energy saving cycle automatically disabled
Settings
100Hr
2500Hr
No filter sign indicator
Standard (PLH/PLA-P·AA(H)/PLA-RP·AA)/Silent (PLH/PLA-
P·KA(H), PCH/PCA)
High ceiling 1 (PLH/PLA-P·AA(H)/PLA-RP·AA)/Standard (PLH/
PLA-P·KA(H), PCH/PCA)
High ceiling 2 (PLH/PLA-P·AA(H)/PLA-RP·AA)/High ceiling
(PLH/PLA-P·KA(H), PCH/PCA)
4 directions
3 directions
2 directions
Not supported
Supported
No vanes
Equipped with vanes (vanes angle setup 1)
Equipped with vanes (vanes angle setup 2)
Disabled
Enabled
D C B A
1Hr.
ON OFF
˚C
CLOCK
FILTER
CHECK MODE
˚C
TEST RUN
ERROR CODE
NOT AVAILABLE FUNCTION
ON/OFF
FILTER
CHECK TEST
TIMER SET
IJKL M
Fig. 8-1
A
TEST RUN
ON/OFF TEMP
FAN AUTO STOP
5
VANE AUTO START
6
LOUVER h
min
SET RESET CLOCK
Fig. 8-2
Mode no.
Mode no.
s Do not carry out this test on the control wiring (low voltage circuit) termi-
nals.
Warning:
Do not use the air conditioner if the insulation resistance is less than 1.0MΩ.
Insulation resistance
8.2. Test run
The following 3 methods are available.
8.2.1. Using wired remote controller (Fig. 8-1)
1 Turn on the power at least 12 hours before the test run.
2 Press the [TEST] button twice. ➡ "TEST RUN" liquid crystal display
3 Press the [Mode selection] button. ➡ Make sure that wind is blown out.
4 Press the [Mode selection] button and switch to the cooling (or heating) mode.
➡ Make sure that cold (or warm) wind is blown out.
5 Press the [Fan speed] button. ➡ Make sure that the wind speed is switched.
6 Switch the wind direction by pressing the [Airflow] or [Louver] button.
➡ Make sure that horizontal outlet, downward outlet, and other wind direction
adjustments are possible.
➡ Check operation of the outdoor unit fan.
7 Release test run by pressing the [ON/OFF] button. ➡ Stop
8 After the checks, always turn off the power.
8.2.2. Using wireless remote controller (Fig. 8-2)
1 Turn on the power to the unit at least 12 hours before the test run.
TEST RUN
2 Press the button twice continuously.
(Start this operation from the status of remote controller display turned off.)
A
and current operation mode are displayed.
TEST RUN
MODE
3 Press the
button to activate
cool air is blown out from the unit.
MODE
4 Press the
button to activate
warm air is blown out from the unit.
FAN
5 Press the button and check whether fan speed changes.
VANE
6 Press the button and check whether the auto vane operates properly.
7 Press the ON/OFF button to stop the test run.
Note:
• Point the remote controller towards the indoor unit receiver while following
steps 2 to 7.
• It is not possible to run the in FAN, DRY or AUTO mode.
Setting no. Initial setting
1
01
2
1
02 2
3
1
03 2
3
1
04
2
1
05
2
Setting no. Initial setting
1
07 2
3
1
08 2
3
1
09 2
3
1
10
2
1
11 2
3
1
12
2
mode, then check whether
COOL
mode, then check whether
HEAT
setting
setting
9