Preliminary Checks - BFT LUX BT Instrucciones De Uso Y De Instalacion

ENGLISH
Thank you for buying this product, our company is sure that you will be more
than satisfied with the product's performance. The product is supplied with
a "Warnings" leaflet and an "Instruction booklet". These should both be
read carefully as they provide important information about safety, installation,
operation and maintenance. This product complies with the recognised
technical standards and safety regulations. We declare that this product is
in conformity with the following European Directives: 2004/108 EEC and
2006/95/EEC (and subsequent amendments).
1) GENERAL SAFETY
WARNING! An incorrect installation or improper use of the product can
cause damage to persons, animals or things.
• The "Warnings" leaflet and "Instruction booklet" supplied with this
product should be read carefully as they provide important information
about safety, installation, use and maintenance.
• Scrap packing materials (plastic, cardboard, polystyrene etc) according
to the provisions set out by current standards. Keep nylon or polystyrene
bags out of children's reach.
• Keep the instructions together with the technical brochure for future refer-
ence.
• This product was exclusively designed and manufactured for the use
specified in the present documentation. Any other use not specified in
this documentation could damage the product and be dangerous.
• The Company declines all responsibility for any consequences resulting
from improper use of the product, or use which is different from that
expected and specified in the present documentation.
• Do not install the product in explosive atmosphere.
• The construction components of this product must comply with the
following European Directives: 2004/108/EEC, 2006/95/EEC and subse-
quent amendments. As for all non-EEC countries, the above-mentioned
standards as well as the current national standards should be respected
in order to achieve a good safety level.
• The Company declines all responsibility for any consequences resulting
from failure to observe Good Technical Practice when constructing clos-
ing structures (door, gates etc.), as well as from any deformation which
might occur during use.
• The installation must comply with the provisions set out by the
following European Directives: 2004/108/EEC, 2006/95/EEC and
subsequent amendments.
• Disconnect the electrical power supply before carrying out any work on
the installation. Also disconnect any buffer batteries, if fitted.
• Fit an omnipolar or magnetothermal switch on the mains power supply,
having a contact opening distance equal to or greater than 3 mm.
• Check that a differential switch with a 0.03A threshold is fitted just before
the power supply mains.
• Check that earthing is carried out correctly: connect all metal parts for
closure (doors, gates etc.) and all system components provided with an
earth terminal.
• Fit all the safety devices (photocells, electric edges etc.) which are needed
to protect the area from any danger caused by squashing, conveying
and shearing.
• Position at least one luminous signal indication device (blinker) where it
can be easily seen, and fix a Warning sign to the structure.
• The Company declines all responsibility with respect to the automation
safety and correct operation when other manufacturers' components
are used.
• Only use original parts for any maintenance or repair operation.
• Do not modify the automation components, unless explicitly authorised
by the company.
• Instruct the product user about the control systems provided and the
manual opening operation in case of emergency.
• Do not allow persons or children to remain in the automation operation area.
• Keep radio control or other control devices out of children's reach, in
order to avoid unintentional automation activation.
MOD
LUX BT
LUX BT 2B
LUX G BT
LUX G BT 2B
8 -
LUX BT
INSTALLATION MANUAL
TYPE OF LOCK
Electric lock
Hydraulic clos./open
Electric lock
Hydraulic clos./open
• The user must avoid any attempt to carry out work or repair on the automa-
tion system, and always request the assistance of qualified personnel.
• Anything which is not expressly provided for in the present instructions,
is not allowed.
• Installation must be carried out using the safety devices and controls
prescribed by the EN 12978 Standard.
2) GENERAL OUTLINE
A compact, sturdy oleodynamic piston, available in a wide range of models
to fit any need and field of operation. It is available in versions both with or
without (reversible) hydraulic lock, that need to be equipped with an electric
lock to hold the gate both closed and open.
The emergency release is obtained with the special key provided (Fig.A
Ref.X).
The pushing force is regulated with extreme precision by means of the con-
trol unit electronic setting. The operation at the end of the stroke is controlled
electronically by a timer in the control panel.
3) THE MAIN PARTS IN THE AUTOMATION (Fig. 1)
M) Permanent magnet motor 24V
P) Hydraulic lobe pump
D) Fluid distributor
C) Cylinder with piston
E) Linear encoder
Standard components: gate post and gate brackets, release key, instruc-
tion booklet.
4) TECHNICAL SPECIFICATIONS
Power supply: ........................................................................................ 24V
Motor: ........................................................................................... 3200 rpm
Power absorption: .............................................................................. 300W
Max. pressure: ................................................................................... 30 bar
Pump delivery: ...............................................................................1,2 l/min.
Pushing force: ...................................................................................3000N
Pulling force: .....................................................................................2600 N
Working stroke: .........................................................................See Table 1
Impact reaction: .................................electronic clutch (with control panel)
Manual manoeuvres: ............................................................ by release key
Max. no. manoeuvres in 24: ...................................................... See table 1
Ambient temperature: ............................................................ - 20°C a 60°C
Protection: ........................................................................................... IP 55
Controller weight: ...............................................................................8,4 kg
Dimensions: ...................................................................................see fig. 1
Circuit oiI: .............................................................................. Idrolux Winter
5) POWER SUPPLY CABLE Fig. 17
6) INSTALLATION OF THE ACTUATOR

6.1) Preliminary checks

Check:
• that the structure of the gate is rigid and strong enough. In any case,
the actuator must push against a reinforced point in the leaf
• that the leaves move manually without excessive effort for the whole of
their stroke
• that the door stops are mounted on the leaves
• If the gate being installed is not new, check whether its components
are worn.
Repair or replace any worn or damaged parts.
Automation reliability and safety are directly influenced by the condition of
the gate's structure.
6.2) Installation values
The values to be known for installation can be found in the table related
to the model being installed (fig. 3-4), with reference also to the diagram
in fig. 5.
TABLE 1
MAX.WING
WORKING
TIME (s)
(m)
17 sec. 2
17 sec. 2
5--2
5--2
STROKE (mm)
(Kg) workin tot
300 270 290
300 270 290
300/800 392 412
300/800 392 412
MANOEUVRES
24h
500
500