Planer Safety Warnings; Additional Safety Warnings; Standard Accessories - Hitachi Koki P 20SF Instrucciones De Manejo

PLANER SAFETY WARNINGS

1. Wait for the cutter to stop before settling the tool
down.
An exposed rotating cutter may engage the surface
leading to possible loss of control and serious injury.
2. Hold the power tool by insulated gripping surface
only, because the cutter may contact its own cord.
Cutting a "live" wire may make exposed metal parts
of the power tool "live" and could give the operator an
electric shock.
3. Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding
the work by your hand or against the body leaves it
unstable and may lead to loss of control.

ADDITIONAL SAFETY WARNINGS

1. Ensure that the power source to be utilized conforms
to the power requirements specifi ed on the product
nameplate.
2. Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, which could cause a serious
accident.
3. When the work area is removed from the power source,
use an extension cord of suffi cient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
4. Prepare a stable wooden workbench suitable for planing
operation. As a poorly balanced workbench creates a
hazard, ensure it is securely positioned on fi rm, level
ground.
5. Do not use the Planer with the blades facing upward (as
stationary type planer).
6. Precaution after fi nishing the planing operation
When the planer is suspended with one hand after
fi nishing the planing operation, ensure that the cutting
blades (base) of the planer do not contact or come too
near your body. Failure to do so could result in serious
injury.
7. Be careful not to injure your hand when attaching or
detaching blades.
8. Before attaching blades, wipe off any chips or other
debris adhering to the blades.
9. If the carbide blade's heights are inaccurate after
above procedures have been completed, carry out the
procedures described below.
10. Always make sure the power switch is OFF and that
the power plug is disconnected before attaching or
detaching the dust adapter.
11. Make sure the dust collector is completely attached.
Failure to do so may result in injury.
12. Take care not to break the catch when attaching or
detaching the dust adapter and chip cover.
13. RCD
The use of a residual current device with a rated residual
current of 30mA or less at all times is recommended.
SYMBOLS
WARNING
The following show symbols used for the machine.
Be sure that you understand their meaning before
use.
P20SF / P20ST : Planer
Read all safety warnings and all instructions.
Only for EU countries
Do not dispose of electric tools together with
household waste material!
In observance of European Directive 2002/96/
EC on waste electrical and electronic equipment
and its implementation in accordance with
national law, electric tools that have reached
the end of their life must be collected separately
and returned to an environmentally compatible
recycling facility.
V
Rated voltage
A
Amperes
Hz
Hertz
W
Watts
n
No-load speed
0
/min
or Revolution or reciprocations per minute
min
–1
Alternating current
kg
Kilograms
Switching ON
Switching OFF
Caution
Disconnect mains plug from electrical outlet
Class II tool

STANDARD ACCESSORIES

In addition to the main unit (1), the package contains the
accessories listed in the below.
○ Box Wrench (for securing cutter blade) .........................1
○ Set Gauge (for adjusting cutter height)..........................1
○ Guide (with set screw)...................................................1
○ Blade Sharpening Ass'y
(for Resharpenable Blade Type) ...................................1
○ Case (P20SA) (not supplied in all areas) ......................1
Standard accessories are subject to change without notice.
APPLICATIONS
Planing various wooden planks and panels. (See Fig. 1)
3
English