Cameo HYDRABEAM 600 RGBW Manual De Usuario página 15

Tabla de contenido

Publicidad

OPERATION / BEDIENUNG / UTILISATION / OPERACIÓN / OBSŁUGA / UTILIZZO
EN
When the spotlight is properly connected to the mains, the motors are reset. Within a few seconds, the spotlight is ready for use and changes to
the mode that was previously selected.
SELECTING THE DMX START ADDRESS
Press the MODE button repeatedly until the LED indicator shows either "Addr" (if no DMX signal is present), or the DMX start address (as soon as a
DMX signal is present, A001 - A512). Press ENTER in both cases, and while all four characters are flashing on the display, the DMX start address can
be set as desired using the UP and DOWN buttons. To confirm, press ENTER. The synchronous control of multiple spotlights (same model) through a
DMX control unit (e.g. DMX console) can be achieved by assigning the spotlights to an identical DMX start address and DMX mode and connecting
them using DMX cables.
SETTING THE DMX MODE
Press the MODE button repeatedly until "ChMO" appears on the display. Press ENTER, and while all four characters are flashing on the display, the
DMX operating mode can be set as desired using the UP and DOWN buttons (6Ch, 11Ch, 20Ch, 32Ch, 60Ch). To confirm, press ENTER. You will find
tables with the channels of the different DMX modes in this manual under DMX CONTROL.
SLAVE MODE
Press the MODE button repeatedly until "SLA" appears on the display. Press the ENTER button and select one of the four different slave modes using
the UP and DOWN buttons and confirm with ENTER.
SLA
SL 1
SL 2
SL 3
SL 4
AUTOMATIC CONTROL
Press the MODE button repeatedly until "AUTO" appears on the display. The AUTO mode starts immediately. Press ENTER. The display now shows
one of the 17 auto programs (Pr00 - PR16). To activate one of the other auto programs, press ENTER again. While all four characters are flashing on
the display, one of the programs can be selected using the UP and DOWN buttons. Confirm the input with ENTER. Using the UP and DOWN buttons,
you can now change the speed of the program by selecting " SPxx " (Speed). Then press ENTER and use the UP and DOWN buttons to select the
desired speed ranging from "SP00" to "SP99" (SP00 = minimum speed; SP99 = maximum speed). Confirm the input with ENTER.
MUSIC CONTROL
Press the MODE button repeatedly until "SoUn" appears on the display. The Music control mode starts immediately. Press ENTER. The display now
shows one of the 17 auto programs in the Music control mode (Pr00 - PR16). To activate one of the other auto programs, press ENTER again. While
all four characters are flashing on the display, one of the programs can be selected using the UP and DOWN buttons. Confirm the input with ENTER.
Using the UP and DOWN buttons, you can now display the menu item "SUxx" to adjust the sensitivity with which programs respond to music signals
(bass pulses). Then press ENTER and use the UP and DOWN buttons to select the desired microphone sensitivity ranging from "SU00" to "SU99"
(SU00 = minimum sensitivity; SU99 = maximum sensitivity). Confirm the input with ENTER.
REVERSE TILT (DMX mode)
The TILT movement direction of a single or all 6 moving heads can be reversed with this function. Press the MODE button repeatedly until "rtiL"
appears on the display. By pressing ENTER, you can now select all (ALL), or a single head (H1 - H6) using the UP and DOWN buttons. Confirm with
ENTER. Using the UP and DOWN buttons, select "Yes" for the reversal of the movement direction and "no" for the normal direction. Confirm with
ENTER.
no reversal of the TILT direction (standard)
Reversal of the movement direction of head 1 - 3
Reversal of the movement direction of head 4 - 6
Reversal of the movement direction of the head 1 - 3 and head 4 - 6
15

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Clhb600rgbw

Tabla de contenido