Declaration Of Conformity - Bosch GAS 35 L SFC+ Professional Manual Original

OBJ_BUCH-1702-004.book Page 19 Friday, December 9, 2016 5:09 PM
Automatic Start/Stop feature*
Rated voltage max. power output min. power output
EU 220–240 V 2200 W
UK 110 V 750 W
UK 240 V 1800 W
CH 230 V 1100 W
* Specification of the allowable load of the connected power tool (coun-
try-specific)

Declaration of Conformity

We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, 2014/30/EU,
2006/42/EC including their amendments and complies with
the following standards: EN 60335-1, EN 60335-2-69,
EN 50581.
Technical file (2006/42/EC) at:
Robert Bosch Power Tools GmbH, PT/ECS,
70538 Stuttgart, GERMANY
Henk Becker Helmut Heinzelmann
Executive Vice President Head of Product Certification
Engineering PT/ECS
Robert Bosch Power Tools GmbH
70538 Stuttgart, GERMANY
Stuttgart, 01.01.2017
Assembly
 Before any work on the vacuum cleaner itself, pull the
mains plug.
Mounting the Vacuum-hose Holder (see figure A)
– Slide the vacuum-hose holders 4 firmly from above into the
retainers 30 intended for this purpose, until they engage.
Mounting the Vacuum Hose (see figure B)
– Mount the vacuum hose 21 onto the hose connection
piece 2 and turn it in clockwise direction to the stop.
Note: While vacuuming, an electrostatic charge develops in
the vacuum hose and accessories caused by the friction of the
dust, which the operator could experience in the form of stat-
ic discharging (dependent on environmental influences and
physical perception).
As a general rule, Bosch recommends using an anti-static vac-
uum hose (accessory) when vacuuming fine dusts and dry
materials.
Mounting VAC Accessories
The vacuum hose 21 and the SFC+ module 20 are equipped
with a clip system, with which the VAC accessories (tool
sleeve 19, elbow 22) can be connected.
Bosch Power Tools
Mounting the Tool Sleeve (see figure C)
– Mount the SFC+ module 20 onto the vacuum hose 21 until
both snap-fasteners 31 of the vacuum hose can be heard
100 W
to engage.
100 W
– Afterwards, mount the tool sleeve 19 onto the SFC+ mod-
ule 20 until both snap-fasteners 31 of the SFC+ module
100 W
can be heard to engage.
100 W
– To disassemble, press both snap-fasteners 31 inward and
pull the components apart.
Mounting Nozzles and Tubes (see figure D)
– Mount the elbow 22 onto the vacuum hose 21 until both
snap-fasteners 31 of the vacuum hose can be heard to en-
gage.
– Afterwards, mount the desired VAC accessory (floor noz-
zle, crevice nozzle, vacuum tube, etc.) firmly onto the el-
bow 22.
– To disassemble, press both snap-fasteners 31 inward and
pull the components apart.
Inserting/Removing a Disposal Bag or Dust
Bag (Dry Vacuuming) (see figures E1 – E2)
For dry vacuuming, a disposal bag 23 or a dust bag (accesso-
ry) can be used. This makes the disposal of the dust easier.
Note: When using a paper filter bag, the semi-automatic filter
cleaning (SFC+) (see "Deactivating the SFC+", page 21),
must, and when using a fleece filter bag, should be shut off.
Inserting a Disposal Bag
– Unlock the latches 9 and remove the vacuum lid 8.
– Insert the disposal bag 23 into the container 1 with the fill-
ing opening toward the front.
– Pull the filling opening over the connection flange into the
recess of the connection flange.
– Make sure that the disposal bag 23 faces completely
against the interior sides of the container 1.
– Fold the rest of the disposal bag 23 over the edge of the
container 1.
– Reattach the vacuum lid 8 again and lock the latches 9.
Removing and Closing the Disposal Bag
– Unlock the latches 9 and remove the vacuum lid 8.
– Pull the full disposal bag 23 toward the rear off of the con-
nection flange.
– Carefully remove the disposal bag 23 out of the vacuum
cleaner without damaging it.
When doing this, pay attention that the disposal bag does
not get caught or ripped open against the connection
flange or other sharp objects.
– Pull the cover off of the adhesive strip, close the disposal
bag and tape it shut.
Afterwards, tie off the disposal bag 23 below the filling
opening with the pulled off cover of the adhesive strip.
Replacing/Inserting the Dust Bag (Accessory)
– Unlock the latches 9 and remove the vacuum lid 8.
– Pull off the full dust bag from the connection flange toward
the rear. Close the opening of the dust bag by folding down
the lid. Remove the closed dust bag from the vacuum
cleaner.
English | 19
1 609 92A 2N5 | (9.12.16)