Assemble Armbar; Stroller Operation - Joie kixx Manual De Instrucciones

Assemble Rear Wheels
Assemble brake assembly to rear legs 5 , assemble rear wheels to brake assembly
tube of rear legs with the flap of the storage basket, and then snap the three
!
Check that wheels are securely attached by pulling on wheel assemblies.
To disassemble rear wheel, detach rear wheel from rear wheel mount
- 1
Assemble Hood
Align the Clips of the hood with the mounts on the tubes, and then slide to assemble the hood.
Please snap the 3 hook and loop fasteners on canopy rear retention and the snaps both sides.

Assemble Armbar

Align the armbar slots with the armbar mounts, and then insert to lock.
To disassemble armbar, press armbar release button
13
The completely assembled stroller is shown as

Stroller Operation

Adjust Recline
There are 4 angles for the backrest.
To recline the backrest, squeeze the recline handle on the back of the seat
- 2
14
To raise the backrest, push up.
!
Make sure the recline is set properly for use.
Use Buckle
Release Buckle
15
Press the center button to release the buckle.
Lock Buckle
Match the waist belt buckle with the shoulder buckle
A "click" sound means the buckle is locked completely.
!
To avoid serious injury from falling or sliding out, always secure your child with harness.
!
Make sure your child is snugly secured. The space between the child and the shoulder harness is about the
thickness of one hand.
! Do not cross the shoulder belts. This will cause pressure on child's neck.
Use Shoulder & Waist Harnesses
!
In order to protect your child from falling out, after your child is placed into the seat, check whether the
shoulder and waist harnesses are at proper height and length.
13
6
. Wrap the connecting
snap buttons 7 .
- 2
8 while pressing the release button.
9
10
11
- 1 - 2
12 12
, and then pull up the armbar.
- 1
14 , pull down on the backrest.
16 - 1 16 - 2
, and click into the center buckle.
- 3
16
- 1
17
Shoulder harness anchor A
- 2
17
Shoulder harness anchor B
17 - 3
Slide adjuster
For larger child, use shoulder harness anchor A and the highest shoulder slots. For smaller child, use shoulder harness
anchor B and the lowest shoulder slots.
8
To adjust the position of the shoulder harness anchor, open the zipper of seat back, turn the anchor to be level
with the side facing forward. Thread it through the shoulder harness slot from back to front.
through the slot that is closest to child's shoulder height.
Use slide adjuster to change the harness length.
- 2
Press the button 20 , while pulling the waist harness to proper length.
Adjust Calf Support
The calf support has 2 positions.
Raise Calf Support
To raise the calf support, just push it upwards.
Lower Calf Support
Press the adjustment buttons on both sides of the calf support
- 2
21
Use Front Swivel Lock
Push up the front swivel locks to maintain the moving direction.
Tip
It is recommended to use swivel locks on uneven surfaces.
Use Brake
To lock wheels, step the brake lever downwards.
To release wheels, step the brake lever forwards.
Tip
Always apply brake when stroller is in stopped position.
Use Hood
To open the canopy, pull canopy toward front.
To fold the canopy, pull canopy toward back.
Adjust Handle
The handle has 3 positions.
To adjust the height of the handle, pull the handle upward or downward
- 1
adjustment button. 26
18
19
- 1
20
- 3
20
- 1
21 , and rotate the calf support downwards.
22
23
24
25
25
- 2
26 while pressing the handle
Rethread it
14