Virutex FP114 Manual De Instrucciones página 16

damaged, have the power tool repaired before use. Many
accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to
bind and are easier to control.
g) Use the power tool, accessories and tool bits etc., in
accordance with these instructions and in the manner
intended for the particular type of power tool, taking
into account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5) Service
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
1.2 SAFETY INSTRUCTIONS FOR
OPERATING THE TRIMMER
I
Carefully read the GENERAL SAFETY
INSTRUCTION LEAFLET enclosed with
the machine documents.
1. Before plugging in the machine, ensure that the
power supply voltage is the same as that stated on the
machine specifications plate. If the power voltage is
higher than the appropriate voltage, the accidents will
be resulted to the operators, and at the same time, the
tool will be destroyed. Therefore, if the power voltage
has not been confirmed, then you shall never plug in
arbitrarily. On the contrary, when the power voltage
is lower than the required voltage, the motor will be
damaged.
2. Always keep hands clear of the cutting area. Always
hold the machine safely.
3. Never use defective or damaged tools.
4. Always use cutter bits with the appropriate stem diame-
ter for the chuck collet and tool speed to be used.
Unplug the machine from the main befo-
re starting any maintenance procedures.
Failure to follow the warnings and instructions may result
in electric shock, fire and / or serious injur.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operat-
ed (cordless) power tool.
If the power cord is damaged, it must be replaced by
our technical service or by personnel qualified, in order
to avoid possible injuries.
• Do not let familiarity gained from frequent use of
16
tools allow you to become complacent and ignore
tool safety principles. A careless action can cause severe
injury within a fraction of a second.
Power tools can produces an electromag-
netic field during operation. This field may
under some circumstances interfere with
active or passive medical implants. To
reduce the risk of serious or fatal injury,
we recommend persons with medical
implants to consult their physician and
the medical implant manufacturer before
operating this power tool.
• Keep handles and grasping surfaces dry, clean and
free from oil and grease. Slippery handles and grasping
surfaces do not allow for safe handling and control of
the tool in unexpected situations.
• Note that when you operate a power tool, please hold
the auxiliary handle correctly, which is helpful when
controlling the power tool. Therefore, proper holding
can reduce the risk of accidents or injuries.
• Follow instruction for lubricating and changing ac-
cessories.
Special safety warnings
• Before work, inspection shall be carried out to see
whether the milling cutter is installed; you should
firmly hold the machine during work. Milling cutter
with appropriate dimension shall be used. Anytime
when the milling cutter is used or changed, it must be
ensured that switch on the machine is on off position.
In order to avoid personal injury done to you and your
bystanders, the power lines must be pulled out of the
socket when the milling cutter is assembled or changed.
• When the machine is used, you will work in dusty
environment; therefore, you should wear mask and
goggles. If you have long hair, you shall wear hair care
cap. You shall not wear loose clothes during work.
• If the power lines are damaged, you shall not touch
them. It is prohibited to use any machine with damaged
power lines. The power lines must be placed behind the
frame (tool operation shall not be affected).
• The machine shall be operated in rain or humid
.
environment. You shall not touch the power lines to
avoid fire or electric shock.
• Before the machine is removed from the workpiece,
you shall cut off power switch and completely stop
the milling cutter.
• The hands shall always be far away from the ro-
tating parts. When the milling cutter is in contact
with the workpiece, you shall not make an attempt to
start the machine.
• After work, the switch shall be turned off first and
then lock knot of guide pillar shall be loosed to make
the machine return to original position.