Product Features; Technical Data; Noise/Vibration Information - Bosch PSM 18 LI Manual Original

14 | English
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is intended for dry sanding and polishing of
wood, filler and varnished surfaces. It is particularly well-
suited for profiles, corners and hard-to-reach areas.

Product Features

The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Battery release button
A)
(2) Battery
(3) Complete dust box (Microfilter system)
A)
(4) Sanding sheet
(5) Sanding plate
(6) SDS slider for sanding plate release
(7) Battery charge indicator
(8) On/off switch
(9) Handle (insulated gripping surface)
(10) Extraction outlet
(11) Filter element (Microfilter system)
(12) Dust extraction adapter
(13) Dust extraction hose
(14) Louvre sanding attachment
A)
(15) Sanding finger, flat
(16) Sanding sheet for sanding finger
(17) Sanding finger, oval
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.

Technical Data

Cordless multi-sander
Article number
Rated voltage
No-load speed
No-load orbital stroke rate
Sanding sheet surface
Orbit diameter
Weight according to
EPTA-Procedure 01:2014
Permitted ambient temperature
– during charging
A)
– during operation and
during storage
Recommended batteries
1 609 92A 4MT | (17.10.2018)
A)
A)
A)
A)
A)
A)
A)
PSM 18 LI
3 603 CA1 3..
V=
−1
min 11000
−1
min 22000
2
cm
mm
kg
°C 0 to +45
°C −20 to +50
PBA 18V...V-.
PBA 18V...W-.
Cordless multi-sander
Recommended chargers
A) Limited performance at temperatures <0 °C

Noise/Vibration Information

Noise emission values determined according to
EN 62841-2-4.
Typically, the A-weighted sound pressure level of the power
tool is 75 dB(A). Uncertainty K=4 dB. The noise level when
working can exceed 80 dB(A).
Wear hearing protection
Total vibration values a
determined according to EN 62841-2-4:
2
a =7 m/s , K=1.5 m/s
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure detailed in EN 62841
and may be used to compare power tools. They may also be
used for a preliminary estimation of vibration and noise
emissions.
The given vibration level and noise emission value represent
the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping the hands warm,
and organising workflows correctly.
Assembly
18
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
104
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
1.6
1.3
Charging the Battery
Use only the chargers listed on the accessories page.
u
Only these chargers are matched to the lithium-ion bat-
tery of your power tool.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
(triax vector sum) and uncertainty K
h
2
.
Bosch Power Tools
PSM 18 LI
AL 18.. CV
AL 22.. CV