wolfcraft 6906 Manual De Instrucciones Original página 46

BDAL 6906_116306906 05.08.13 17:32 Seite 46
Lock the machine plate as shown in Fig. 17. The table is now ready for stationary sawing, please also read the section on stationary sawing
with the hand-held circular saw.
Cutting depth adjustment
If the cutting depth of the hand held circular saw is changed, the height of the riving knife must also be adjusted to guarantee the max. 5 mm safety
distance to the circular saw blade. First loosen the riving knife using the Allen wrench. Then set the hand-held circular saw to the required cutting
depth. Tighten the cutting depth lock again. Attach and position the setting gauge together with the riving knife as illustrated in Fig. E.1 to E.8.
Vertical mitre cuts
The hand-held circular saw must be realigned for vertical mitre cuts. Set the required mitre angle on the hand-held circular saw. Retract the protective
pendulum hood on the hand-held circular saw and position the machine centrally over the saw gap. Release the cutting depth lock on the circular
saw and set the machine to the maximum cutting depth. Tighten the cutting depth lock again (Fig. F.1, F.2). Loosen the Allen key and turn the riving
knife until it is positioned exactly central in relation to the circular saw blade (Fig. F.3).
CAUTION: Check the distance between the foremost tooth on the saw blade to the front edge of the saw gap. This distance must be less than 20 mm
(Fig. F.4).
Tighten the Allen screw (Fig. F.5).
CAUTION: Align the saw blade parallel in the saw gap while ensuring that the circular saw blade is always positioned centrally in relation to the
riving knife.
Attach the two side stops so that their surfaces are in full contact with the machine's base plate. Then attach the two clamping claws. Secure another
side of the base plate. Install the angle bracket with two side stops first. Make sure they are in full contact with the base plate. In the same way,
install an angle bracket with two side stops on the opposite side. Attach the two clamping claws. The two clamping claws must be installed as close
to the longer side of the base plate as possible (Fig. G).
Adjust the safety distance between the riving knife and circular saw blade using the setting gauge.
Close the machine plate (Fig. H.1). Fit the individual parts to the riving knife as shown in the illustration (Fig. H.2). Tighten the screw and the knurled
nut connected to the riving knife and loosely tighten the screw and knurled nut in the front of the housing (Fig. H.3). Loosen the riving knife
fastening using the Allen wrench (Fig. H.4). Slide the riving knife towards the circular saw blade at the same angle as the saw blade (Fig. H.5). Slide
down the riving knife until at least one circular saw blade tooth reaches the housing of the setting gauge (detailed view H.6). Now tighten the front
knurled nut (Fig. H.6). When the Allen screw is tightened, the safety distance between the circular saw blade and the riving knife is adjusted to max.
5 mm (Fig. H.7). Unscrew the setting gauge from the riving knife again. Lock the machine plate as shown in Fig. 17 and check once again that the saw
blade rotates freely (Fig. I).
CAUTION: Make sure that the saw blade is aligned centrally in relation to the riving knife (detailed view in Fig. I) and that the max. safety distance of
5 mm between the circular saw blade and riving knife is maintained (detailed view in Fig. H.6), otherwise the hand-held circular saw must
be realigned.
CAUTION: Before starting work, always check that the riving knife and fixing parts are fastened tightly!
The table is now ready for stationary sawing, please also read the section on stationary sawing with the hand-held circular saw.
Warranty
Dear hobbyist!
You have purchased a high-quality wolfcraft
standards, and undergo intensive development and test phases before leaving the factory. Constant controls and regular tests during their
manufacture, ensure a high quality standard. Sound technical developments, and reliable quality controls warrant for the right choice of appliance.
We provide a warranty of 10 years from the day of purchase on the wolfcraft
The warranty only covers damage to the item purchased, and only such damage that can be attributed to faulty material und poor workmanship.
The warranty does not cover defects and damage that must be attributed to improper use or insufficient maintenance. Nor does the warranty cover
the usual wear and tear as well as defects and damage, of which the customer has been aware when purchasing the equipment.
Warranty claims can only be asserted by producing the invoice or the till receipt.
The warranty granted by wolfcraft
contract, price reduction, claims for damages or reimbursement of expenses).
Declaration of Conformity pursuant to Directive 2006/42/EC on Machinery, Annex II A
wolfcraft GmbH in D-56746 Kempenich, Wolff-Str. 1, hereby declares that this product (MASTER cut 1500) conforms
to Directive 2006/42/EC on Machinery. TUEV Rheinland LGA Products GmbH, Tillystrasse 2, 90431 Nürnberg. BM: 60087567 0001
Conformity with the following standards: DIN EN 60745-1, DIN EN 60745-2-5, DIN EN 60745-2-11
Kempenich, 02.08.2013
Michael Bauseler
Person authorized to sign the Declaration of Conformity and to compile the technical documentation.
(Management/Technology/Logistics; wolfcraft GmbH)
appliance, which we know you will enjoy using. wolfcraft
®
® does not in any way restrict your statutory consumer rights (i.e. contract performance, withdrawal from the
t
appliances are built to high technical
®
® product you acquired, provided it is exclusively used for DIY purposes.
46