List Of Components - Chicco Urban Instrucciones De Uso

not fitted with the hood or sun canopy to
prevent the risk of suffocation.
· To prevent the risk of overheating or
suffocation, never leave the stroller
under the sun with the rain cover fitted
to it.
· Use only the rain cover supplied or
approved by the manufacturer.
· Prevent the stroller from coming into
contact with salt water. It may cause the
formation of rust.
· Do not use the stroller on the beach.
· When not in use, the stroller must be
kept away from the reach of children.

LIST OF COMPONENTS

· Frame
· Seat
· 2 rear wheels
· 2 front wheels
· Bumper bar
· Basket
· Mattress for pram configuration
· Raincover
With the "COLOUR PACK" (not part of the basic stroller
configuration, available to purchase separately), you will also have
the following components:
· Canopy
· Seat insert
· 2 shoulder strap pads and one crotch strap cover pad (comfort
kit)
· Legcover / Pram apron.
To assemble these components please refer to paragraph
"COLOUR PACK".
NOTE: A Chicco Autofix Fast or Chicco Keyfit car seat can be
installed on the Urban stroller, using the specific "Car seat
adapter" (sold separately). To properly assemble the ''Car seat
adapter'', refer to the relative instruction manual.
ADVICES FOR CLEANING AND MAINTENANCE
This product requires periodical maintenance. Cleaning and
maintenance operations must be performed exclusively by an
adult.
CLEANING
The lining of the stroller and the carrycot cannot be removed.
Clean the fabric parts using a wet sponge and neutral soap. Clean
the plastic parts periodically using a wet cloth. Dry the metal
parts if they come into contact with water in order to avoid the
formation of rust. Do not use solvents or abrasive products.
The padded mattress of the carrycot with removable lining can be
washed following the indications included in the materials label.
To clean the components of the Colour pack (purchased
separately), follow the indications included on the materials labels.
The washing symbols and relative meanings are indicated below:
Wash by hand in cold water
Do not bleach.
Do not tumble dry.
Do not iron.
Do not dry clean.
MAINTENANCE
Lubricate the removable parts with dry silicon oil if needed. Check
the state of wear of the wheels on a regular basis, and keep them
clean from dust and sand. Make sure that all plastic parts that slide
on the metal tubes are clean from dust, dirt and sand, in order to
avoid frictions that may compromise the optimal performance of
the stroller. Keep the stroller in a dry place.
FIRST ASSEMBLY OF THE STROLLER
1. Press the grey button inside the circular articulated joint and at
the same time, rotate the handle tube as shown in figure 1.
2. Then extend the structure completely, by opening the front leg
tube until hearing a locking click (fig. 2-2A).
3. Insert the front wheel into the relative hole until hearing a
locking click (fig. 3). Repeat the same operation for the second
front wheel.
4. To assemble the rear wheels Insert the wheel's pin into the rear
leg tube as shown in fig. 4. Repeat the same operation for the other
wheel.
WARNING: Before using the stroller, make sure that the wheels
are well secured to the structure.
5. The front part of the basket has a shaped area. Assemble the
basket positioning the shaped part on the front tube, using the
relative press stud buttons (fig. 5) and repeat the operation for the
rear part of the basket (fig. 5A). To complete the assembly, thread
the straps located on the front part of the basket through the ''D''-
shaped rings located on the front legs of the stroller, securing the
straps with the press stud buttons (fig. 5B).
WARNING: Do not load the basket with weights exceeding 3 kg.
ASSEMBLY OF THE SEAT: STROLLER CONFIGURATION
The packaging includes the disassembled stroller's frame and seat.
6. To assemble the seat, position the metal support located on the
base of the seat as shown in fig. 6.
Then close the zip located at the bottom of the seat, wrapping the
metal component (fig. 6A).
7. Fasten buckle A located externally in the seat's foot area, as
shown in Fig. 7, then fasten buckle B positioned externally under
the seat (fig. 7A) and tension the belt acting as shown in Fig. 7B.
WARNING: Check the belt's tension on a regular basis.
8. To attach the seat, introduce the two hooks shown in Fig. 8 in
the relative slots located inside the circular articulated joints of
the stroller (fig. 8A) until hearing a locking click.
WARNING: Make sure the seat is installed properly by pulling it
upward.
9. The seat can be assembled on the stroller in both directions:
in forward facing configuration (Fig. 9) and parent facing
configuration (fig. 9A).
10. To remove the seat, press the grey side buttons and pull
upward (fig. 10). These operations must not be performed when
the child is inside the seat.
WARNING: Do not remove the seat from the stroller when the
child is inside of it.
SEAT ADJUSTMENTS
Once the seat is assembled on the frame, it can be adjusted in
three different positions.
11. The entire seat can be adjusted by pressing simultaneously the
buttons located above the central articulated joint (fig. 11).
12. The angle of the backrest can be adjusted compared to the
seat, by pressing the clip as shown in fig. 12.
LEG REST ADJUSTMENTS
13. It is possible to adjust the leg rest in various positions, by
pressing simultaneously the buttons shown in fig. 13.
23