Environmental Protection - Metabo KFM 9-3 RF Instrucciones De Manejo

en ENGLISH
1. Lift the adjustment ring (14) and turn in such a
way that the indexable insert (21) does not
remove any material. (chamfer height = 0 mm)
2. Loosen the two clamping screws (13).
3. Turn the graduated ring (13) until the chamfer
height 0 mm is shown.
4. Tighten the two clamping screws (13).
5. Carry out trial cut.
9. Cleaning
Chips and particles can deposit at the cutter head.
This can lead to blockage of the cutter head.
Regularly clean the cutter head and its
surroundings and remove chips and particles.
It is possible that particles deposit inside the power
tool during operation. This impairs the cooling of the
power tool. Conductive build-up can impair the
protective insulation of the power tool and cause
electrical hazards.
The power tool should be cleaned regularly, often
and thoroughly through all front and rear air vents
using a vacuum cleaner or by blowing in dry air.
Prior to this operation, separate the power tool from
the power source and wear protective glasses and
dust mask.
10. Troubleshooting
10.1 Mains powered machines:
- Overload protection: There is a MAJOR
reduction in load speed. The motor temperature
is too high! Allow the machine to run at idle speed
until it has cooled down.
- Overload protection: There is a MINOR
reduction in load speed. The machine is
overloaded. Reduce the load before continuing to
work.
- Metabo S-automatic safety shut-down: The
machine has SHUT DOWN by itself. If the slew
rate of the current is too high (for example, if the
machine suddenly seizes or kickback occurs), the
machine switches off. Switch off the machine
using the slide switch (4). Switch it on again and
continue to work as normal. Try to prevent the
machine from seizing. See chapter 3.1.
- Restart protection: The machine does not
start. The restart protection is active. If the mains
plug is inserted with the machine switched on, or if
the power supply is restored following an
interruption, the machine does not start up. Switch
the machine off and on again.
10.2 Cordless machines:
- The electronic signal display (8) lights up and
the load speed decreases. The temperature is
too high! Run the machine in idling until the
electronics signal indicator switches off.
- The electronic signal display (8) flashes and
the machine does not start. The restart
protection is active. The machine will not start if
the battery pack is inserted while the machine is
on. Switch the machine off and on again.
10
11. Accessories
Use only genuine Metabo accessories.
Use only accessories which fulfil the requirements
and specifications listed in these operating
instructions.
Fit accessories securely. If the machine is operated
in a holder: Secure the machine well. Loss of control
can cause personal injury.
A Indexable inserts
HM-indexable insert 45° ................... 6.23560
HM-indexable insert R 2 ................... 6.23561
HM-indexable insert R 3 ................... 6.23562
B Chargers: ASC Ultra, ASC 15, ASC 30 and others
C Battery packs with different capacities. Use
battery packs only with voltage suitable for your
power tool.
For a complete range of accessories, see
www.metabo.com or the catalogue.
12. Repairs
Repairs to electrical tools must ONLY be
carried out by qualified electricians!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. See
www.metabo.com for addresses.
You can download a list of spare parts from
www.metabo.com.

13. Environmental Protection

Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Special notes regarding cordless machines:
Battery packs may not be disposed of with regular
waste. Return faulty or used battery packs to your
Metabo dealer!
Do not allow battery packs to come into contact with
water!
Before disposal, discharge the battery pack in the
power tool. Prevent the contacts from short-
circuiting (e. g. by protecting them with adhesive
tape).
14. Technical Data
Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
U = Voltage of battery pack
n = no-load speed (maximum speed)
n = On-load speed
1
P = Rated input power
1
P = Power output
2
I = Current at 120 V
120 V
m = Weight with smallest battery pack/weight
without cord
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).