Flotec FPSE 3601A Serie Manual Del Usuario página 3

Safety
READ AND FOLLOW
SAFETY INSTRUCTIONS!
This is the safety alert symbol. When you see this
symbol on your pump or in this manual, look for
one of the following signal words and be alert to the
potential for personal injury:
warns about hazards that will cause serious
personal injury, death or major property damage if
ignored.
warns about hazards that can cause serious
personal injury, death or major property damage if
ignored.
warns about hazards that will or can cause
minor personal injury or property damage if ignored.
The label NOTICE indicates special instructions which
are important but not related to hazards.
Carefully read and follow all safety instructions in this
manual and on pump.
Keep safety labels in good condition.
Replace missing or damaged safety labels.
1. Read this manual carefully. Failure to follow these
instructions could cause serious bodily injury and/or
property damage.
ATTACH ORIGINAL RECEIPT HERE FOR WARRANTY CONSIDERATION.
FLOTEC warrants that the products specified in this warranty are free from defects in material or workmanship.
If within the duration of product use by the product owner, any FLOODMATE
(FPSC4550A), Sewage Ejector (FPSE3601A), Pedestal Pump (FPPSS5000), or Utility Pump (FPSC1725X), shall prove to
be defective, it shall be repaired or replaced at FLOTEC's option, subject to the terms and conditions set forth below.
General Terms and Conditions
Owner must pay all labor and shipping charges necessary to replace product covered by this warranty. This warranty
shall not apply to acts of God, nor shall it apply to products which, in the sole judgement of FLOTEC, have been sub-
ject to negligence, abuse, accident, misapplication, tampering, alteration; nor due to improper installation, operation,
maintenance or storage; nor to excess of recommended maximums as set forth in the owner's manual.
Requests for service under this warranty shall be made by returning the product to the Retail outlet or to FLOTEC as
soon as possible after the discovery of any alleged defect. FLOTEC will subsequently take corrective aciton as promptly
as reasonably possible.
This warranty sets forth FLOTEC's sole obligation and purchaser's exclusive remedy for defective products.
FLOTEC SHALL NOT BE RESPONSIBLE FOR ANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT DAMAGES
WHATSOEVER. THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES,
IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE.
Some states do not allow the exclusion or limitation of incidental or consequential damages or limitation on how long
an implied warranty lasts, so the above limitations or exclusions may not apply to you. Although this warranty identi-
fied specific remedies you may also have other rights and remedies.
E-Mail: info@flotecwater.com • Web Site: http://www.flotecwater.com
FLOTEC • P.O. Box 342 • Delavan, WI U.S.A. 53115
Phone: 1-800-365-6832 • Fax: 1-800-526-3757
2. Check your local codes before installing. You must
comply with their rules.
3. Vent sewage or septic tank according to local codes.
4. Do not install pump in any location classified as
hazardous by National Electrical Code, ANSI/NFPA
70-1990.
Hazardous voltage. Can shock, burn or
cause death. During operation, the pump is in water.
To avoid fatal shocks, proceed as follows if pump needs
servicing:
5A. Disconnect power to outlet box before unplugging
pump.
5B. Take extreme care when changing fuses. Do not
stand in water or put your finger in fuse socket.
5C. Do not modify cord and plug. When using cord and
plug, plug into a grounded outlet only. When wiring
to a system control, connect pump ground lead to
system ground.
6. Do not run pump dry. Dry running can overheat
pump, (causing burns to anyone handling it) and will
void warranty.
7. Pump normally runs hot. To avoid burns when ser-
vicing pump, allow it to cool for 20 minutes after
shut-down before handling it.
8. In normal service, motor should not need oiling.
Motor has been filled at the factory with a special
oil.
® 7000 (FP0S6000A), IRONMATE
2
®