Working With The Roller Edge Guide; Setting For Mitre Cuts (Only For Kss Design); Working With Guide Rail; Working With Position Indicator - Mafell MF 26 cc Manual De Instrucciones

attached to the left or right of the machine. The
cutting range on the right-hand side amounts to
approx. 170 mm (6 45/64 in.)and on the left-hand side
to approx. 345 mm (13 37/64 in.).

When working with the parallel stop, set the
cutting depth indicator 10 (Fig. 8) by turning it
into the bottom position (without rail).

The rods of the parallel stop have a scaling,
which refers to the left-hand side of the saw
blade.

You can adjust the cutting width after releasing
the wing screws 19 (Fig. 2) by moving the limit
stop accordingly and afterwards retightening the
wing screws.
In addition, by simply turning it around, the parallel
stop can also be used as double support to improve
groove-cutting machine guidance (guide surface for
the workpiece edge is pointing upwards). Now the
machine can be guided along a lath that is fastened
on the workpiece.

5.10 Working with the roller edge guide

The parallel stop 20 (Fig. 3) is used to work parallel to
an already existing edge. The limit stop can be
attached to the left or right of the machine. The
cutting range on the right-hand side amounts to
approx. 0 - 100 mm (0 – 3 15/16 in.) and on the left-
hand side to approx. 23 - 230 mm (29/32 – 9 1/16
in.).

When working with the roller edge guide, set the
cutting depth indicator 10 (Fig. 8) by turning it
into the bottom position (without rail).

The rods of the parallel stop have a scaling,
which refers to the left-hand side of the saw
blade.

You can adjust the cutting width after releasing
the wing screws 19 (Fig. 2) by moving the limit
stop accordingly and afterwards retightening the
wing screws.
Now the machine can be guided along a narrow
workpiece running below the base plate.

5.11 Setting for mitre cuts (only for KSS design)


Release the limit stop 40 (Fig. 7) and adjust the
angle according to the scale on the guide rail.

Retighten the limit stop.

Using the two stop bolts on the bottom side of
the guide rail, apply the machine to the
workpiece to be machined. Then carry out the
cut by advancing the machine.

After the cut, return the saw to its starting
position by retracting it.
Quick adjustment of the repeater stops 43 (Fig. 7)

Using the Allen key 4 (Fig. 2), turn the
hexagonal bolt in the repeater stop by approx. ½
revolution counter clockwise.

Push the repeater stop against the permanently
set stop from the side facing away from 0°, so
that it rests behind the stop.

Tighten the hexagonal bolt in the repeater stop.

Also set the repeater stop on the opposite 0°
side accordingly.

5.12 Working with guide rail


Place the machine onto the guide rail such that
the groove 24 (Fig. 6) of the base plate rests
above the spring and is guided by it.

Set the cutting depth indicator 10 (Fig. 8) into
the top position by turning (with rail). Thus, the
scale can also be used with the rail.

5.13 Working with position indicator

Use the position indicator to align
the guide rail to a centre marking of
the guide groove. It is included with
the machine or tools (for
plasterboard milling cutter and
aluminium compound milling
cutter).
Proceed as follows:

Fit the position indicator 42 (Fig. 6) onto the rib
of the guide rail.

Move the position indicator on the rail up to the
marking.

Move the rail with position indicator until the
front (red edge) of the marking indicator agrees
with the marking.

Place the machine onto the rail (the tool is now
aligned with the centre of the marking).
-30-