Chauvin Arnoux STATOP 4850 Manual De Instrucciones página 27

Level Index Parameter
XXXX Process value
YYYY Setpoint value
ASP1 Setpoint of absolute alarm (if A1.md = FS.hi or FS.Lo )
Setpoint of following alarm (if A1.md ≠ FS.hi or FS.Lo )
Timer (if A1.SF = to.on or to.oF )
rAmP Ramp of temperature rise
oFSt Manual offset of proportional band
ASP2 Setpoint of absolute alarm (if A2.md = FS.hi or FS.Lo )
Setpoint of following alarm (if A2.md ≠ FS.hi or FS.Lo )
ShiF
Display offset
Pb
Proportional band channel 1 (hot)
ti
Integral time
td Derivative time
AhY1 Hysteresis of relay of alarm A1
AhY2 Hysteresis of relay of alarm A2
hYSt Hysteresis on ON-OFF control
Addr Digital address of the controller
Lo.SC
Lowest limit of scale
hi.SC
Top limit of scale
PL.1 Power limit on channel 1 (hot)
PL.2 Power limit on channel 2 (cold)
inPt Type of input
unit Unit of display
rESo
Resolution of display
Con.A Direction of control channel 1 (hot)
A1.md Behaviour of alarm A1
A1.SF Special functions for alarm A1
A2.md Behaviour of alarm A2
A2.SF Special functions for alarm A2
CYC Channel 1 modulation cycle (hot)
C.CYC Channel 2 modulation cycle (cold)
C.Pb
Channel 2 proportional band (cold)
d-b
Dead band (band offset C.Pb/Pb)
Adjustment range or possible choice
Lo.SC...hi.SC
Lo.SC...hi.SC
-111,0...+111,0°C
0...9999 minutes
0...55,55°C/minute
0...100% ( ti must equal 0)
Lo.SC...hi.SC
-111,0...+111,0°C
-111,0...+111,0°C
0...+200,0°C (0 = ON-OFF action)
0...3600 seconds
0...1000 seconds
0...+11,0°C
0...+11,0°C
0...+11,0°C
0...40
see text
see text
0...100%
0...100%
J-tC J couple
k-tC K couple
t-tC T couple
E-tC E couple
b-tC B couple
r-tC R couple
S-tC S couple
n-tC N couple
Pt.dn Pt 100 DIN
Pt.JS
Pt 100 JIS
4-20
4...20 mA
0-20 0...20 mA
0-1v 0...1 V
0-5v 0...5 V
1-5v 1...5 V
0-10 0...10 V
°C degree centigrade
°F degree Fahrenheit
p.u other (V or mA)
no.dP
no decimal
1.dP
1 decimal
2.dP 2 decimals
dirt direct
rEvr reverse
dv.hi high gap
dv.Lo low gap
db.hi high symmetrical
db.Lo low symmetrical
FS.hi high absolute
FS.Lo low absolute
nonE none
Lt.Ch locking state
hoLd
prohibit 1st fault
Lt.ho
Lt.Ch + hoLd
to.on timer
to.oF timer
idem parameter A1.md
nonE none
Lt.Ch locking state
hoLd prohibit 1st fault
Lt.ho Lt.Ch + hoLd
Cool proportional control output 2 (cold)
0...99 seconds
0...99 seconds
0,0...+200,0°C
-111,0...+111,0°C
27
Preset
value
+100,0°C
+10,0°C
0,00°C/min
0,0%
+10,0°C
0,0°C
+10,0°C
120 s
40 s
0,0°C
0,0°C
0,0°C
0
-17,7°C
+537,7°C
100%
100%
K couple
°C
1 decimal
reverse
high gap
none
high gap
none
20 s
20 s
+10,0°C
0,0°C