Maintenance And Cleaning - Oase Water Jet Lightning Instrucciones De Uso

- GB -
Alignment of the Water Jet Lightning and setting the intensity of the water jet (L, M)
Prior to starting work, disconnect the power plugs of all units in the water (J)!
Adjusting the angle of inclination (L)
The diagram shows the shapes of the water jet at various angles of inclination of the Water Jet Lightning.
− Undo the fastening screw (34) at the unit foot (33).
− Swing the Water Jet Lightning to the desired angle of inclination.
− Tighten the fastening screw (34) at the unit foot (33).
Setting the water jet (M)
For the Water Jet Lightning, the intensity of the water jet can be set at the valves of the Y distributor (9).
− Turn the respective valve clockwise: to reduce the water flow.
− Turn the respective valve counter-clockwise: to increase the water flow.
Pos: 97 /Alle Produkte/Dummy_module/Abstand 6 pt @ 7\mod_1196627997106_0.doc @ 41651
Pos: 98 /Alle Produkte/Überschriften/H1 Bedienung @ 7\mod_1196625148604_121.doc @ 41443
Operation
Pos: 99 /Lampen/Wasserspieltechnik/Water Jet Lightning/BED_Water-Jet-Lightning @ 8\mod_1221040043053_121.doc @ 52265
4 pre-programmed water features can be selected with the manual transmitter.
After commissioning and with each new start of the unit, program 1 is automatically selected.
P0
P1
P2
P3
P4
Selecting the next program: Button 1
Selecting the previous program: Button 2
Note:
− From changing light colour, it is possible to set one colour only by pressing the buttons 1 and 2 simultaneously.
− If the Water Jet Lightning is switched by means of a timer, always program 1 is started.
Pos: 100 /Lampen/Wasserspieltechnik/Water Jet Lightning/Handsender einlernen und löschen Water-Jet-Lightning @ 8\mod_1221040104351_121.doc @ 52291
The manual transmitter contained in the scope of delivery is already taught in to the 12 V control box. Each further
manual transmitter has to be newly taught in for the 12 V control box.
Manual transmitter teach-in (K)
The 12 V control box (2) is equipped with a teach-in button (31) to be able to carry out the manual transmitter teach-in.
− Insert a pin (32) in the opening for the teach-in button (31).
− Actuate the teach-in button (31) using the pin (32) for approx. 1 sec.
− Press any button of the manual transmitter for at least 1 sec.
Deleting the manual transmitter (K)
− Actuate the teach-in button (31) using a pin (32) for at least 5 sec.
All manual transmitters saved in the 12 V control box (2) are deleted.
Note: A maximum of 10 manual transmitters can be set to the receiver. The manual transmitter has a maximum range
of 80 m. Obstacles between transmitter and receiver, a low battery in the manual transmitter, or electro-magnetic
radiation of electrical equipment will impair the range.
Pos: 101 /Alle Produkte/Dummy_module/Abstand 6 pt @ 7\mod_1196627997106_0.doc @ 41651
Pos: 102 /Alle Produkte/Überschriften/H1 Reinigung und Wartung @ 7\mod_1196625212761_121.doc @ 41469

Maintenance and cleaning

Pos: 103 /Lampen/Wasserspieltechnik/Water Jet Lightning/WAR_Reinigung und Wartung_Water-Jet-Lightning @ 8\mod_1221040256101_121.doc @ 52343
Prior to starting work on the units, disconnect the power plugs of all units in the water (J)!
Cleaning the Water Jet Lightning (N, O)
− Separate the upper section (34) from the housing bottom section (36) with a slight twist, then remove together with
the O-ring (35) .
− Remove the foam filter (37) and unscrew the LED unit (38) .
− Clean all parts under running water using a soft brush.
− Squeeze out the foam filter (37) several times under running water.
Cleaning the pump (D, P)
− Loosen the union nut (14) at the Y distributor (15).
− Unscrew the reduction piece (16) from the pump (4) and remove the Y distributor (15).
− Pull the motor housing (39) out of the engagement holder of the plug-in filter (40).
− Remove the pump housing (41) with a slight turn, and remove the impeller (42) .
− Clean all parts under running water using a soft brush.
Unit reassembly (N, O, D, P)
− Reassemble the units in the reverse order.
Pos: 104 /Alle Produkte/Dummy_module/===== Seitenwechsel ===== @ 0\mod_1125648978015_0.doc @ 1630
14
Unit off, stand-by mode
Constant water jet
White light activated
Constant water jet
Changing light colours
Pulsating water jet
White light activated
Pulsating water jet
Changing light colours
Changing light colour can be returned to by pressing the buttons 1 and 2 simultaneously again.