Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
This button can be pressed at any time during the system setup process to complete
the p_ocess
_
At the System Setup Menu, press the SYSTEM SETUP button
_ The changed settings
are entered and the on-screen
display turns off
• On-screen
display signals
Signals input to the AVR 2803
On screen dJspla V sig[lal output
VIDEO si_na_i[iput
Swideo signal
VIDEO MONITOR OUT video
S video MONITOR OUT video
iack (yel_owl
i[iput jack
signal output jack {yellowl
slg[la_output iack
1
×
x
O
©
2
©
x
{}
×
3
×
0
x
O
4
O
0
x
O
({}: Signal
X: NOslglla_l
(O: Orl screen slglla_s output
X: On scleea sigrlals not output)
NOTES:
• The on-screen
display
signals
are not output
fronl
the
color
difference
(conlponent)
video
signal
MQN]TOR
OUT jacks
• For 4 above, the on-screen
display signals are output
to the VIDEO MONITOR
OUT video signal output
jack (yellow)
if the monitor TV is not connected
to the S-video MONITOR OUT video signal output jack
[]
REMOTE
CONTROL
UNIT
• The included
remote
control unit (RC-925) can be used to operate not only the AVR-2803 but other remote
control compatible
DENON components
as well
In addition,
the memory
contains
the control signals for
other remote control units, so it can be used to operate non-Denon
remote
control compatible
products
_)
Remove the remote control unit's rear cover
_2) Set
three
R6P/AA
batteries
in
the
battery
compartment
in the indicated direction
(.3} Put the rear cover back on
Notes on Batteries
• Use R6P/AA batteries
in the remote
control unit
• The batteries
should
be replaced
with
new ones
approximately
once a year, though this depends on
the frequency
of usage¸
• Even if less than a year has passed, replace
the
batteries with new ones if the set does not operate
even when
the remote
control
unit is operated
nearby the
set
(The included battery
is only for
verifying opeiation
Replace it with a new battery as
soon as possible)
• When inserting the batteries,
be sure to do so in the
proper direction,
following
the "@" and "@" marks
m the battery compartment
• To prevent damage or leakage of battery fluid:
•
Do not use a new battery
together
with
an old
one
•
Do not use two different
types of batteries
•
Do
not
short-circuit,
disassemble,
heat
or
dispose of batteries
in flames
• Remove the batteries from the remote
control unit
when
you do not plan to use it for an extended
period of time
• If the battery fluid should leak, carefully
wipe the
fluid off the inside of the battery compartment
and
insert new batteries
• When
replacing
the
batteries,
have
the
new
batteries
ready
and insert
them
as quickly
as
possible
30°
• Point the remote control unit at the remote sensor
on the main unit as shown on the diagram
• The remote control unit can be used from a straight
distance of approximately
7 meters from the main
unit, but this distance
will be shorter
if there are
obstacles
in the way or if the remote control unit is
not pointed
directly at the remote sensor
• The remote
control
unit
can be operated
at a
horizontal angle of up to 30 degrees with respect to
the remote
sensor
NOTES:
• It may be difficult
to operate
the remote
control
unit
if the
remote
sensor
is exposed
to direct
sunlight
or strong artificial light
• Do not press buttons on the main unit and remote
control unit simultaneously
Doing so may result in
malfunction
• Neon s_gns or other
devices
emitting
pulse-type
noise nearby
may result
in malfunction,
so keep
the set as far away from such devices as possible
17
Publicidad
Tabla de contenido
