Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
•
We greatly
appreciate your purchase of the AVR-2803.
•
To he sure you take maximum
advantage
of all the features the AVR*2803 has to offer, read these
instructions
carefully
and use the set properly.
Be sure to keep this manual
for future reference,
should any questions
or problems arise.
"SERIAL NO.
PLEASE RECORD UNIT SERIAL NUMBER
ATTACHED TO THE REAR OF THE
CABINET
FOR FUTURE
REFERENCE"
•
INTRODUCTION
Thank you for choosing
the DENON AVR-2803
Digital
Surround
AV receiver
This remarkable
component
has
been engineered
to provide superb surround
sound listening with home theater sources such as DVD, as well as
providing outstanding
high fidelity reproduction
of your favorite music sources
As this product is provided with an immense array of features,
we recommend
that before you begin hookup and
operation that,
ou review the contents
of this manual before proceeding
TABLE OF CONTENTS
[._i] Before Using ........................................................
3
_
Cautions on Installation ........................................
3
Cautions on Handling ...........................................
3
Features ...............................................................
4
®Connections
.....................................................
4+8
Part Names and Functions
..............................
8, 9
Setting up the System ..................................
9-17
Remote Control Unit ...................................
17+22
Operation .....................................................
22-27
[_
Surround ......................................................
27-31
DSP Surround
Simulation ............................
31 +34
Listening to the Radio .................................
35+38
Last Function Memory .......................................
38
Initialization
of the Microprocessor
.................... 38
Troubleshooting
...........................................
38, 39
Additional
Information
.................................
39+44
Specifications
.....................................................
45
• ACCESSORIES
Check that the following parts are included in addition to the main unit:
[]
BEFORE USING
Pay attention
to the following
before using this
unit:
• Moving
the
set
TO prevent
shot[
circuits
or
damaged
wires
in the
connection
cords,
always
unplug
the
power
cord
and
disconnect
the
connection
cords
between
811
other
audio
components
when
moving
the
set
• Before
turning
the
power
switch
on
Check
once
again
that
all connections
are
proper
and that
there
are not problems
with
the connection
cords¸
Always
set the
power
switch
to the
standby
position
before
connecting
and
disconnecting
connection
cords¸
• Store this instructions
in a safe place.
After reading,
store this instructions along with the
warranty
in a safe place¸
• Note
that the illustrations
in this
instructions
may differ from
the actual
set for explanation
purposes.
[]
CAUTIONS
ON INSTALLATION
Noise or disturbance
of the picture may be gene+ated
if this unit or any other electronic
equipment
using
microprocessors
is used near a tuner or TV
If this happens, take the following
steps:
• Install this unit as far as possible from the tuner or
TV
• Set the antenna
wires from the tuner or TV away
from
this
unit's
power
cord
and
input/output
connection
cords
• Noise
or disturbance
tends
to occur
particularly
when using indoor antennas or 300 _Johms feeder
wires
We recommend
using
outdoor
antennas
and 75 £_/ohms coaxial cables.
For heat dispersal,
leave at least
10 cm of space
between
the top,
back
and
sides
of this
unit
and
the wall
or other
components,
10 cm or more
wall
_
Operating
instructions ........................................
1
_2_Service station list ..............................................
1
(.3_Remote control unit (RC-925) ............................
1
_}R6P/AAbatteries
................................................
3
®AMIoop
antenna ................................................
I
_FM
indoorantenna
.............................................
I
@
14:
t_;
®
[]
CAUTIONS
ON HANDLING
• Switching
the input function
when
input jacks
are not connected
A clicking
no_se may be
produced
if the
input
function
is switched
when
nothing
is connected
to
the input iacks
If this happens, either turn down the
MASTER VOLUME
control or connect components
to tile input iacks
• Muting
of PRE OUT
jacks,
HEADPHONE
jacks
and SPEAKER terminals
The
PRE
OUT
iacks,
HEADPHONE
jack
and
SPEAKER
terminals
include
a muting
circuit
Because
of this,
the
output
signals
are greatly
reduced for several seconds after the power switch
is turned on or input function,
surround
mode or any
other-set-up
is changed
If the volume is turned up
during
this time, the output
will be very high after
the muting
circuit
stops
functioning
Always
wait
until the muting circuit turns off before adjusting the
volume
• Whenever
the power
switch
is in the J[
OFF
state, the apparatus
is still connected
on AC line
voltage
Please be sure to unplug
the cord when
you
leave home for, say, a vacation.
3
Publicidad
Tabla de contenido
