Dsp Surround - Denon AVR-2803 Instrucciones De Operación

Surround parameters
CINEMA EQ, (Cinema Equalizer):
Tile Cinema EQ function gently decreases the level of the extreme high frequencies, compensating for
ovedy-bbght sounding motion picture soundtracks Select this function if tile sound from the front speakers
is too bright
This function only works in the Dolby Pro Logic, Dolby Digital, DTS Surround, DTS NEO:6 and WIDE SCREEN
modes (The same contents are set for all operating modes)
D,COMR (Dynamic Range Compression):
Motion picture soundtracks have tremendous dynamtc range (the contrast between very soft and very loud
sounds) For listening late at night, or whenever the maximum sound level Js lower than usual, the Dynamic
Range Compression allows you to hear all of the sounds in the soundt_ack (but with reduced dynamic range)
(This only works when playing program sources recorded in Dolby Digital or DTS) Select one of the four
parameters {"OFF", "LOW", "MID" (middlel or "HI" {high)) Set to OFF for normal listening
LFE (Low Frequency Effect):
This sets the level of the LFE (Low Frequency Effect) sounds included in the source when playing program
sources recorded in Dolby Digital or DTS
If the sound produced from the subwoofer sounds distorted due to the LFE signals when playing Dolby Digital
or DTS sources when the peak limiter is turned off with the subwoofer peak limit level setting (system setup
menu), adjust the level as necessary
Program source and adiustmenf range:
I Dolby Digital: -10 dB to 0 dB
2 DTS Surround: -lg dB to 0 dB
When DTS encoded movie software is played, it is recommended that the LFE LEVEL be set to
0 dB for correct DTS playback,
When DTS encoded music software is played, it is recommended that the LFE LEVEL be set to
-10 dB for correct DTS playback,
TONE:
This adjusts the tone control (See "Surround parameters _" on page 33)
SB OH OUT:
(1) Dolby Digdal/DTS source
"OFF" ..................... Playback is conducted without using the surround back speaker
"NON MTRX" ......... Playback is conducted using the surround back speaker
The same signals those of the surround channels are output from the surround back
channels
"MTRX ON" ............ Playback is conducted using the surround back speaker
Surround back channel is reproduced using digital matrix processing
"NRML (OFF)" Playback is conducted without using the surround back speaker
"NRML (ON)" ......... Playback is conducted using the surround back speaker
Surround back channel is reproduced using digital matrix processing
(2) Other source
"OFF" ..................... Playback is conducted without using the surround back speaker
"ON" ....................... Playback is conducted using the surround back speaker
NOTE: This operation can be performed directly using the "SURROUND BACK" button on the main unit's
panel
[] DSP SURROUND SIMULATION
• The AVR-2803 is equipped with a high performance DSP (Digital Signal Processor) which uses digital signal
processing to synthetically recreate the sound field One of seven preset surround modes can be selected
according to the program source and the parameters can be adiusted according to the conditions in the
listening room to achieve a more realistic, powerful sound These surround modes can also be used for
program sources not recorded in Dolby Surround Pro Logic or Dolby Digital
1 ROCK ARENA Use this mode to achieve the feeling of a live collcett ill an arena with reflected sounds coming
from all directions
2 JAZZ CLUB This mode creates the sound field of a live house with a low ceiling and hard walls This mode
glves iazz a very vivid realism
MQNO MOVIE
3 {NOTE 1) Select this when watching monaural movies for a gloater sense of expansion
4 VIDEO GAME Use this to enioy video game sources
Select this to emphasize the sense of expansion for music sources recorded in stereo Signals
5 MATRIX consisti[ig of the difference component of the input signals (the component that provides the
sense of expansion) processed for delay are output from the surround cha[_nel
6 VIRTUAL Select this mode to eiljoy a vir tual sound fie_d, produced from the front 2 <'hannel speakers
In this mode, the signals of the front left channel are output from the left surround channel, the
slg[la_s of the front rlght chan[lel are Output from the dght surround channel, and the same (in
7 5CH/7CH STEREO phase) component of the [eft and right channels is output from the centel channel This mode
provides all speaker surrour_d soured, but without d_recdo[_a_ steering ef feels, and works w_th any
stereo program source
Depending on the program source being played, the effect may not be very noticeable
In this case, try other surround modes, without worrying about their names, to create a sound field suited
to your tastes
NOTE 1: When playing sources recorded in monaural, the sound will be one-sided if signals are only input to
one channel deft or right), so input signals to both channels If you have a source component with only
one audio output (monophonic camcorder, of c) obtain a "Y" adaptor cable to split the mono output
to two outputs, and connect to the L and R inputs
Personal Memory Plus
This set is equipped with a personal memodze function that automatically memobzes the surround modes
and input modes selected for the input different sources When the input source is swdched, the modes set
for that source last time it was used are automatically recalled
The surround parameters, tone control settings and playback level balance for the different output
channels are memortzed for each surround mode
31